高水头船闸输水廊道反弧门水弹性振动试验研究

本文简要介绍水弹性振动模型试验的相似准则，用近似满足水弹性相似准则的有机玻璃模型对－高水头船闸反弧形阀门进行流激振动试验研究．试验表明阀门的振动是随机振动，不仅有质量振动而且有结构振动，有若干阶模态被激发参与振动。在开门和关门过程中，阀门面板脉动压力和阀门振动是不大的，与葛洲坝船闸类似阀门间歇开启的振动水平相当。由于常压模型不能正确模拟空化现象，对于廊道内可能产生的空泡溃灭所引起的阀门振动尚需通过减压模型进行研究。     

�;��ȶ�����״̬�µ������Ծ���������

本文提出了油井稳定生产状态下的脉冲试井数学模型,利用时间和空间叠加原理求得其解析解。并用非线性回归分析方法来进行脉冲试井分析。     

Physicochemical characteristics and leachability of scale and sludge from Bulalo geothermal system, Philippines

Scale and sludge from Bulalo geothermal field, Philippines, have been characterized by whole rock analysis, radioactivity counting, size analysis, light microscopy, scanning electron microscopy, and X-ray diffraction. Their leachability was assessed by regulatory leaching procedures and by sequential extraction. Both scale and sludge consisted mostly of oxides of Si, Al, and Fe with no radionuclides detected. The scale had 10% S content. Sulfides and silicates were important phases in both samples having size ranges from submicron to 2 mm. Geothermal soils at Bulalo have higher than normal soil levels of As, S, Cu, Cr, Zn, and Pb but regulatory leaching tests indicated that these elements are not released. However, the sequential extraction showed that As, Cu, and Zn were leachable under extreme conditions.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

液压随动系统在线监测与故障诊断系统

介绍了集随动系统在线监测与故障诊断于一体的智能系统。利用基于知识的诊断推理技术与神经网络技术相结合的方法构建了随动系统在线故障诊断专家系统，使得神经网络推理与基于符号的知识诊断控制、解释有机地结合起来，取长补短，大大提高了系统的工作效率和诊断可靠性。     

Test Generation for Crosstalk-Induced Faults: Framework and Computational Results

Due to technology scaling and increasing clock frequency, problems due to noise effects lead to an increase in design/debugging efforts and a decrease in circuit performance. This paper addresses the problem of efficiently and accurately generating two-vector tests for crosstalk induced effects, such as pulses, signal speedup and slowdown, in digital combinational circuits. These noise effects can propagate through a circuit and create a logic error in a latch or at a primary output. We have developed a mixed-signal test generator, called XGEN, that incorporates classical static values as well as dynamic signals such as transitions and pulses, and timing information such as signal arrival times, rise/fall times, and gate delay. In this paper we first discuss the general framework of the test generation algorithm followed by computational results. Comparison of results with SPICE simulations confirms the accuracy of this approach.     

Selective area epitaxy of CdTe

We have performed selective area epitaxy (SAE) of CdTe layers grown by molecular beam epitaxy using a shadow mask technique. This technique was chosen over other SAE techniques due to its simplicity and its compatibility with multiple SAE patterning steps. Features as small as 50 microns × 50 microns were obtained with sharp, abrupt side walls and flat mesa tops. Separations between mesas as small as 20 microns were also obtained. Shadowing effects due to the finite thickness of the mask were reduced by placing the CdTe source in a near normal incidence position. Intimate contact between the mask and the substrate was essential in order to achieve good pattern definition.     

Formation of GaAsP interface layers monitored by reflectance anisotropy spectroscopy

Reflectance anisotropy spectroscopy (RAS) has been used to study As-by-P exchange during metalorganic vapor phase epitaxy. The study focuses on the processes occurring during switching from GaAs to GaInP, especially the effect of purging PH₃ over a GaAs surface. GaAsP/GaAs superlattices of different periodicity were grown and the P-content was determined by high-resolution x-ray diffraction and correlated to the RAS spectra. From the temperature dependence of the P-content, an activation energy of 0.56 eV was estimated for the incorporation mechanism. In addition to the insights into the processes at mixed group-V heterointerfaces, our study demonstrates the reproducibility of RAS transients that thus can be used for process monitoring.     

On the Yustova threshold plates

A response to criticism of threshold plates for the study of color vision developed at the Mendeleev All-Russia Research Institute of Metrology and published in 1994 is presented. The critics base their conclusions on colorimetric testing and the examination of the plates. In response to the article by M. V. Danilova and J. D. Mollon [4]. __________ Translated from Izmeritel’naya Tekhnika, No. 1, pp. 37–39, January, 2007.     

用双向扭转圆柱组合螺旋弹簧实现扭矩测试

利用单个圆柱螺旋扭转弹簧扭转原理,给出了一种用双向扭转圆柱组合螺旋弹簧实现扭矩测试的方法。根据扭转弹簧模型,给出了预紧力、加载的证明,并对实验结果进行分析;该结构用于扭矩测试系统既实用可靠,又简单易加工;降低了测试系统的成本,具有很高的实用价值。