Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

试论双点后方交会简便公式

根据双点后方交会的图形特点和已知条件，列出了方程组，推导出了双点后方交会直接计算座标的简便公式，同时求出了精度计算公式，以供测量人员参考     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

掺气减蚀设施水力计算的改进

结合小湾工程泄洪洞模型试验进行了11种挑跌坎型和6级流量的试验观测，据此提出了特别适用于大单流量条件的射流出射角修正式，提出了射流近底流速的选取原则.与实验资料对比证明本文计算方法有足够精度。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。     

具有再生反馈雷达的角跟踪性能闭环测试

本文论述了用雷达跟踪目标最大角速度和角加速表征具有再生反馈雷达角跟踪性能的合理性,并论述了用单片机测试雷达跟踪目标最大角速度和最大角加速的方法。     

凸轮机构基圆半径的确定方法及其分析

基圆半径的确定方法，除了用图解法和试算法外，还可用解析法和图解分析法求解。４种方法各有优缺点，设计时要根据具体情况选择。     

海上靶场角度量录取系统的研制

本文详细叙述了海上靶场角度量录取糸统的组成、测试原理及其功能设计，简要介绍了该系统在靶扬的应用情况．     

Flows in rectangular microchannels driven by capillary force and gravity

Capillary phenomena was studied and discussed by the scholars about 200 years ago, but the progress was slow due to the limited equipment and manufacture precision of the microchannel. In recent years, because of the rapid development of MEMS and micromachining, many applications of the capillary flow is widely developing in some modern processes, such as underfilling of flip chip, flow in microfluidic chip or biochip, and a variety of other fields.