The role of the surface free energy in the selection of a suitable excipient in the course of a wet-granulation method

Pellets containing metronidazole were produced in a centrifugal granulator, with hydroxypropylcellulose (Klucel LF®) as binding agent, and corn starch, microcrystalline cellulose (Vivapur 101®) and lactose as excipients. The wettability of the pharmaceutical powders was assessed by means of contact angle measurements, and the dispersive and polar surface energies were determined. The spreading coefficients, the work of adhesion and the work of cohesion were calculated and correlated with the pellet properties (friability, bulk and tapped density, and porosity). The aim was to investigate the role of the surface free energy of one- and two-component powder compositions in pellet production. The interactions between the particles were found to be connected with the measured pellet parameters. It was concluded that, in the course of the growth of the pellets, the particle sizes of the pharmaceutical powders and the interactions between them are important. If the work of cohesion of the binder is lower than the work of cohesion of the substrate and the work of adhesion, then the optimal amount of the binding agent is that which coats the particles uniformly in minimal quantity and in continuous layer.     

薄板坯连铸浸入式水口结构数值模拟

使用有限元计算方法开展薄板坯连铸浸入式水口流场的研究 ,分别对水口不同浸入深度的流场分布、水口出口不同角度的流场分布进行计算。结果发现 :水口的浸入深度在 30 0mm时较为合理 ;水口的出口角度以R1 5、60°、45°为宜     

臭氧氧化处理法对聚丙烯表面涂装性的改良 Ⅳ.聚丙烯表面亲水性和涂膜剥离强度的关系

讨论了用臭氧氧化法对聚丙烯表面进行涂装性改良时,丙烯均聚物、乙烯-丙烯嵌段共聚物及无规共聚物表面以接触角表示的亲水性和涂膜剥离强度之间的关系。结果表明,当聚丙烯表面对水的接触角在84°附近时,可反应型涂料的涂膜剥离强度将出现最大值。在此也证明了涂膜的剥离破坏存在着接着破坏和凝集破坏两种机理,当接触角减小到84°及84°以上时,剥离发生在聚丙烯和涂层的界面上产生接着破坏;当接触角减小到84°以下时,剥离发生在聚丙烯的表面氧化层相中,产生凝集破坏。     

High resolution solid state 13C n.m.r. of butadiene grafted polypropylene

¹H dipolar decoupled ¹³C n.m.r. experiments with the aid of the magic angle spinning technique have been used to determine the graft content and the isomer content of the polybutadiene grafts in a graft copolymer with isotactic polypropylene.     

The effect of Al content on the wettability between liquid iron and MgOAl2O3 binary substrate

In the present study, the wettability between liquid iron with two different Al contents and MgOAl₂O₃ binary substrates was studied in reducing atmosphere. The contact angles between liquid iron with 18?ppm Al and MgO, MgO·Al₂O₃, Al₂O₃ were 133.5°, 113.7°, 126.9° respectively. With the variation of the substrate composition, the contact angles for the intermediate binary phases of the three components (MgO, MgO·Al₂O₃, Al₂O₃) obeyed the Cassie theory. In the experiment using iron with 370?ppm Al, all the contact angles were higher than that using low Al-containing iron. The surface of the iron drop was covered with an oxide layer, which mainly consisted of many small particles. With the variation of the substrate gradually from MgO to Al₂O₃, the composition of the oxide layer changed from MgO·Al₂O₃ to CaOAl₂O₃. The formation of the oxide layer prevented the spreading of liquid iron, leading to the increase of the contact angle.     

聚合物熔体在圆锥短口模的挤出胀大方程

深入讨论了聚合物熔体在不同长径比、不同角度圆锥短口模的挤出胀大现象及机理，利用生产用挤出机进行不同角度的圆锥短口模实验。结果表明，圆锥短口模挤出过程中，熔体在收敛流道受到拉伸流变，导致强烈的入口弹性效应，表现为熔体在短口模挤出时显著的挤出胀大。理论和实验研究结果进一步表明不同圆锥口模入口角对实验材料表现出有不同的挤出胀大值。     

低氟含量低表面能自清洁氟碳涂料的研究

以氟单体和丙烯酸酯类单体通过聚合物的分子结构设计，合成了一类总氟含量不超过12％的低氟含量的含氟丙烯酸树脂，所制备的氟碳涂料的涂层的表面能低，具有自清洁功能。分析了该涂层中极性与非极性官能团的分子取向机理，测定了纯水水珠在不同含氟单体均聚物和共聚物清漆漆膜上以及在含氟丙烯酸树脂涂层上的接触角，探明了含氟丙烯酸树脂涂层的总氟含量与表面能的关系、含氟官能团在涂层中的分布，探讨了低氟含量的含氟丙烯酸树脂涂料的涂层自清洁机理。     

基于光学测角和无线数据传输技术的传递对准

为了解决动基座传递对准中航向角估计困难的问题,提出了基于光学测角和无线数据传输技术的传递对准技术方案。通过对航母舰体挠曲变形模型的建立和对光学测角原理的分析,构建了相应的卡尔曼滤波器。仿真结果表明,利用卡尔曼滤波能够估计出姿态误差角和光学测量装置自身的等效零偏。当对光学测量装置的等效零偏补偿之后,航母在匀速航行条件下,姿态误差和速度误差都可以得到快速的收敛,其中航向角误差可以在4 s内收敛到0.7'以内,明显提高了子惯导航向角的对准速度。     

光纤光栅传感器中磁场测量稳定性研究

为了减小光纤光栅磁场传感器中线性双折射和入射起偏角对系统稳定性的影响,提高测量系统的准确性,提出一种减小线性双折射和起偏角大小对系统输出影响的设计方案。研究了基于法拉第效应的光纤光栅磁场传感器系统,得出系统输出电压与磁场的关系式,并通过降低线性双折射和确定入射起偏角改善了系统的输出特性。仿真表明:该方法可以有效抑制测量过程中线性双折射造成的非线性关系,从而提高磁场测量的稳定性。     

南京地区固定式安装太阳能电池板最佳倾角设计

对于固定安装的光伏电池板,其倾角的选择直接影响到所接收到的太阳辐射量,从而决定着太阳能利用系统的性能。本文在获得南京地区辐射资料的基础上,采用太阳辐射量气象学模型,针对任意方位角固定式安装的光伏电池板给出了最佳倾角的计算结果。该结果可为南京地区太阳能系统的设计与安装提供理论依据,并为相近地区太阳辐射量计算提供参考。