Effect of Lateral Cracks on Fracture Toughness Determined by the Surface-Crack-in-Flexure Method

The surface-crack-in-flexure (SCF) method uses a Knoop indenter to create small, semielliptical surface precracks in beam specimens. Lateral cracks may interfere with the primary median crack and cause errors of up to 10% in determination of fracture toughness, particularly for materials for which the fracture toughness is ∼3 MPa·m^1/2 or less. Although the residual-stress-damage zone is ground or polished away by hand by removing 4.5–5 times the indentation depth, this amount may not be sufficient to completely remove the lateral cracks in low-fracture-toughness materials. A series of tests were conducted on sintered alpha silicon carbide with different amounts of material removed after indentation. Once the lateral cracks were fully removed, the SCF results concurred with single-edged-precracked-beam and chevron-notched-beam data collected in accordance with ASTM Designation C1421. A simple remedy for the SCF method is to examine the outer ground surface for remnants of lateral cracks before fracture and to remove more material if necessary.     

安全壳钢衬的初始后屈曲分析

基于Ｄｏｎｎｅｌｌ的非线性板壳理论，认为钢衬壳是一种有特殊缺陷形状的钢衬板，用初始后屈曲渐进分析理论，研究了在温度应力作用下缺陷钢衬板即钢衬壳的初始后屈曲性态。计算了一个四点铆固钢衬壳模型，同时给出了铆钉间距等参数对钢衬壳屈曲极值温度的影响。     

离散效应存在时孤子脉冲的增强压缩

在群速度不匹配的条件下，提出一种提高孤子脉冲压缩效应的新方法．研究表明，若使信号脉冲与泵浦脉冲存在一适当的初始延时，则不但可以提高离散效应单独存在时信号脉冲的压缩比，而且可以提高孤子脉冲的压缩质量．     

石油天然气长输管线用钢新进展

本文介绍了１９９０年以来国外在石油天然气长输管线用钢方面的最新成果，以获得较低的强度和韧性匹配为目的经轧后加速冷却工艺后的钢的强度的预测和控制；具有优良抗氢致裂纹的含硼、微碳、低硫、Ｎｂ－Ｔｉ微合金化、Ｘ６５－Ｘ８０级管线钢的开发，满足于特殊性能要求的ＴｉＯ处理技术及Ｘ８０级ＴｉＯ细化晶粒钢、低硬度和低屈强比钢，以及复合板加工耐腐蚀钢管的生产。     

型钢厂试轧美标H型钢性能分析研究

分析了型钢厂试制热轧美标H型钢低温冲击韧性偏低的原因，并在此基础上提出了对生产工艺的优化与改进。     

机器人足球比赛系统中的机器人任务分配方法

针对基于遗传算法的多机器人任务分配方法中,由于初始种群是随机产生不能很好地表征整个解空间,而容易陷入局部最优解的问题,提出一种新的多机器人任务分配方法。该方法根据机器人效用函数值来确定个体基因,从而产生初始种群,并引进分层遗传算法来实现具有不同最优基因的群体分开演化。仿真实验表明,该方法比传统的遗传算法有更高的寻优效率和更快的收敛速度。     

一种制做三维牙——颌骨光弹性模型的新方法

本文提出一种用“整体浇注法”制做三维牙——颌骨光弹性模型的新方法,即用价格便宜的石膏做阴模,先制出与真实牙几何相似的牙光弹性模型和模拟牙周膜的乳胶套,将它们粘接好,然后将其放入颌骨石膏阴模的适当位置,浇入环氧树脂混合液,用“二次固化法”进行固化,即可制成三维牙——颌骨整体光弹性模型。此法能保证模型与实物的严格几何相似和牙周的边界条件相似,使实验精度大大提高且工艺简单、成本低。     

Water table fluctuation with a random initial condition

The nonlinear Boussinesq equation is used to understand water table fluctuations in various ditch drainage problems. An approximate solution of this equation with a random initial condition and deterministic boundary conditions, recharge rate and aquifer parameters has been developed to predict a transient water table in a ditch-drainage system. The effects of uncertainty in the initial condition on the water table are illustrated with the help of a synthetic example. These results would find applications in ditch-drainage design.Notation A / tanh t - a lower value of the random variable representing the initial water table height at the mid point - a+b Upper value of the random variable representing the initial water table height at the midpoint - B tanh t - C 4/ - h variable water table height - h mean of the variable water table height - h _m variable water table height at the mid point - h _m mean of the variable water table height at the mid point - K hydraulic conductivity - L half spacing between the ditches - m ₀ initial water table height at the mid point - N Uniform rate of recharge - S specific yield - t time of observation - x distance measured from the ditch boundary - (4/SL)(NK)^1/2 - (L/4)(N/K)^1/2 - dummy integral variable     

X80管线钢焊接热影响区的韧性分析

X80管线钢在焊接过程中,热影响区由于受到焊接过程热的作用,其组织和性能会发生较大的变化.韧性是天然气长输管线的重要性能,采用热模拟技术、现代工程测试手段和显微分析方法,分析了不同热输入参数下X80管线钢焊接热影响区粗晶区(CGHAZ)韧性(夏比冲击功和CTOD)的差异及其原因.在一定范围内,较高焊接热输入下CGHAZ的韧性比较低热输入下CGHAZ的韧性明显高,超过一定范围,随着热输入的增加韧性激剧下降.造成不同热输入下韧性差异的根本原因是由CGHAZ显微组织的差异引起的.较低的热输入下CGHAZ中产生了一定量的低碳马氏体,从而导致韧性较差.     

冶炼工艺对GH871合金涡轮盘韧性的影响

研究了AIM ESR和VIM ESR两种冶炼工艺对GH871合金涡轮盘三种韧性指标的影响,结果表明:冶炼工艺对该合金在室温、650℃拉伸和缺口冲击韧性影响较小,采用VIM ESR冶炼工艺可以显著提高GH871合金在700℃拉伸韧性和I型裂纹平面应变的断裂韧性。