综合高速效应的凝析气藏流入动态

当井底压力低于露点压力时,凝析液在近井地带开始析出并不断聚集产生凝析油堵塞现象。因此,在制定凝析气井工作制度时,通常以控制生产压差为指导思想,往往忽略高速流动下凝析气液相变的非平衡特征。对于凝析气体系,当外界温压变化速度超过凝析气液的相平衡速度时,凝析气体系相变滞后,开始呈现非平衡特征,即凝析液的析出量随着压降速度的增加而减小。凝析气在向井筒流动的过程中,近井区高速流动使凝析气产生非平衡相变,凝析气在比较高的压降速度下流入井筒,使得凝析液来不及析出。在分析非平衡相变规律与近井地带凝析气渗流参数分布的基础上,评价凝析气液流动过程中的非平衡特征,给出了考虑非平衡相变的凝析液饱和度分布计算公式,并进行了产能预测结果对比。实例分析表明,可以通过适当放大生产压差,增加凝析气液相变非平衡特征,减小井筒附近的凝析液饱和度,提高气井产能与气藏开发效果。     

SO4^2-／ZrO2固体超强酸的制备及其催化合成ETBE的研究

采用沉淀一浸渍法制备了负载型SO4^2-／ZrO2固体超强酸催化剂，运用IR、XRD等方法表征所制备催化剂的物化性质。结果表明，所制备的催化剂具有固体超强酸催化剂的特征，酸性与焙烧温度有关，适当提高焙烧温度有利于样品酸强度的提高，但焙烧温度过高会导致脱硫；浸渍液H2SO4浓度高有利于提高催化剂的硫含量，但是浓度过高，会在催化剂上形成硫酸盐，从而降低催化剂的比表面积和酸性。采用制备的催化剂气相催化乙醇与叔丁醇合成乙基叔丁基醚反应，乙基叔丁基醚的选择性为54．71％。     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

硅胶固载光敏剂的合成及其在反式维生素D3光敏异构化为顺式维生素D3中的应用

采用丙二酸作为连接,针9－蒽甲醇连接到硅胶上生成硅胶固载的光敏剂。利用此因相光敏剂分别在乙醇和甲苯溶液中敏化反式维生素D3。实验结果表明，此固相光敏剂能够有效地敏化反式维生素D3为顺式维生素D3的反应，并且非常容易从反应体系中分离出来。     

Niobium-containing catalysts—the state of the art

This review article is devoted to the materials containing niobium, which have been discovered or developed in the past few years and exhibit the potential application in heterogeneous catalysis. Niobium oxides and mixed oxides as well as sulfides, nitrides (oxynitrides), carbides (oxycarbides), and phosphates are considered. Among the catalytic processes in which Nb-containing materials were tested, liquid and gas phase oxidation is described in details, and the role of niobium in the prevention of the catalyst from SO₂ poisoning is mentioned.     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

基于C6711处理器cdma2000 1X系统前向信道信号的处理

在cdma20001x前向信道中,要对一段信号进行传送,一般选用QPSK调制,因为QPSK调制比QAM更适合噪音环境。采用TI6000系列的TMS320C6711芯片处理前向信道信号,可以对复杂性和实时性较高的信号做采集、量化、编码、调制等实时处理,主要功能通过软件编程实现,从而使系统具有结构灵活、可靠性高、可扩展等优点。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。