Friction Stir Welding of Ceramic Particle Reinforced Aluminium Based Metal Matrix Composites

The mechanical and microstructural properties of 6061+20% Al₂O_3p and 7005+10% Al₂O_3p aluminium based metal matrix composites joined by friction stir welding were analyzed in the present study. The two materials were welded into the form of sheets of 7 mm thickness after T6 treatment and were tested in tension at room temperature. The microstructure of the joints was observed by optical microscopy and the fracture surfaces were analyzed by employing a scanning electron microscope equipped with field emission gun in order to study the micromechanisms involved during the deformation.     

汽车摩擦片厚度测量装置驱动电路的研究

本文通过对摩擦片厚度在线测量装置系统构成的全面分析，对其驱动电路子系统进行了理论探索和技术研究，完成了相应的电路设计、误差分析及器件选择等工作，并进行了具体的实验验证，证明该驱动电路具有良好的性能，可圆满实现摩擦片厚度在线检测和实时分析的工作任务。     

Low Temperature Elastic Constants of Polycrystalline MgB2

We have used a resonant ultrasound spectroscopy technique to measure the bulk and shear modulus of fully dense, polycrystalline MgB₂ between 4 and 300 K. Both moduli show good agreement with published first principle calculations. The internal friction shows a broad maximum around 40 K.     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

Relationship between Relaxation Internal Friction Peak at about 200℃(f≈1Hz)and Bainitic Transformation In a CuZnAl Alloy

The present investigation showed that the re-laxation peak at about 200℃ (f≈1Hz) was relatedto bainitic transformation in a CuZnAl alloy.Thepeak decreased when bainite precipitated.Theactivation energy of the peak was the same as theapparent activation energy of bainitic transforma-tion.According to the relations between the peakand the bainitic transformation,the mechanism ofthe peak has been discussed.     

适用于稠油开采的游梁式抽油机设计分析

在稠油开采中,抽油杆在液体中运动时,所受到的摩擦阻尼力很大,有时高达几十千牛。上冲程时,该力有加大悬点载荷的作用;下冲程时,该力使抽油杆下行困难,甚至悬点载荷为零。为了开采稠油,必须根据其特点设计适应的游梁式抽油机。文章分析了稠油用抽油机的受力特点,提出了该类抽油机的设计要求。     

Internal drift effects on the diffusion of Ag in CdTe

Anomalous diffusion profiles of Ag in single crystalline CdTe were observed using the radiotracer ¹¹¹Ag. The diffusion anneals were performed at 800 K under Cd or Te vapor and in vacuum with low Ag concentrations. The measured Ag profiles directly reflect the distribution of the self-interstitials and vacancies of the Cd sublattice and are the result of chemical self-diffusion which describes the variation of the deviation from stoichiometry of the binary crystal as a function of depth and time. It turned out that the spread of the Ag dopant essentially is determined by the drift of the charged defects within the electric field caused by the distribution of the extrinsic and intrinsic defects.     

双组分树脂冷压法制备摩擦材料

研究甲、乙双组分液体树脂作为粘结剂制备制动摩擦材料的冷压工艺方法，甲组分树脂为硼改性腰果壳油树脂，乙组分树脂为三聚氰胺改性酚醛树脂。该工艺可使模压料在室温下具有良好的成型效果，在固化处理中不使用夹具，可以使成型料具有良好的保型效果。冷压制备的制动摩擦材料具有硬度低、摩擦系数稳定和恢复性好等特点。     

二硫代磷酸硫化氧钼与硫,磷添加剂的复配特性研究

研究了二烷基二硫代磷酸硫化氧钼（ＭｏＤＴＰ）摩擦改进剂及其与硫、磷、硫－磷型添加剂复合的抗磨减摩性能。试验表明，经过适当复配后，这类合活性元素的添加剂对ＭｏＤＴＰ的抗磨减摩性能均有增效作用，同一类型添加剂的活性愈高，增效作用愈显著。同时利用扫描电镜和Ｘ－射线能谱仪进行摩擦副表面膜的形貌照相及元素分析，对复合作用的机理进行了初步探讨。     

Cr12型模具钢锻造内部裂纹产生的原因及预防

基于Cr12型钢种的特点，归纳了Cr12钢锻造时内部裂纹的类型，分析了内部裂纹产生的原因并提出了相应的预防措施。