我国炼油技术开发的若干思考与建议

分析了我国炼油工业面临的挑战，世界炼油工业的发展趋势，提出了我国炼油技术开发要围绕符合国情的清洁燃料生产技术，炼油与化工结合的炼油技术，适合现有炼油装置技术改造、提高技术水平，降低加工成本的技术，渣油转化技术，煤制油，天然气制油技术，炼油厂智能化的技术，减少炼油厂烟尘排放的技术等7个方面开展工作的具体建议。     

紧凑式换热面瞬态实验中的全程直接配比法

在紧凑式换热面的瞬态实验中，为获得准确的实验结果，不仅要建立符合试验工况的理 论解，而且还要选择合适的配比方法，以便尽可能减小测量误差对配比结果的影响．本文就瞬态实 验的配比，提出了一种新的基于计算机的全程直接配比法，由于它采用了所有可用测试点进行配 比并且其理论解与实测值的配比误差是通过最小搜索步长来控制的，因此，实验结果的准确性和 可靠性优于通常应用的间接配比法和选点配比法．     

国外水电技术的发展

概述了国外水电建设中的技术发展情况，着重论述了物探、高坝和抗震、厂房优化布置、洞内消能、预应力混凝土衬砌隧洞、大坝检测和老坝修复等几项重大技术在水电工程中的应用。     

DFMC在水利机械产品开发中的应用研究

分析了DFMC(大规模定制设计)关键技术及相关技术,提出了运用该项技术开发产品企业应作好的前期准备,研究了水利机械产品"大型移动启闭机"的定制开发。     

APPLICATION OF SITE-SPECIFIC NATURAL ISOTOPE FRACTIONATION (SNIF-NMR) OF HYDROGEN TO THE CHARACTERIZATION OF EUROPEAN BEERS

More than one hundred samples of European beers have been investigated by the new SNIF-NMR method which is based on 2H NMR at the natural abundance level and enables site-specific natural isotope fractionation factors in ethanol to be determined. The relative (R) and absolute (D/H)_i, parameters are shown to be characteristic of the country where the beers are brewed and the observed variations are explained in terms of cereal composition, water resource, and manufacturing processing (fermentation, yeast, temperature cycle). These new parameters find analytical and mechanistic applications in the identification of a beer and in the investigation of a fermentation process.     

从76届SEG年会看综合物化探技术的发展方向

文中在介绍76届SEG年会的展商、展台及会场专题报告与论文发布情况的基础上，阐述了参加本届SEG年会的体会，指出了重磁电技术发展的四个趋势：向海洋勘探技术方向发展、向复杂区综合勘探技术方向发展、向三维联合处理和三维可视化解释技术发展、向直接圈定和检测油气方向发展。     

新城金矿采场落矿控制爆破技术

新城金矿为蚀变岩型金矿床,由于受地质构造影响,顶板稳定性较差,局部和较大面积的顶板冒落现象时有发生,为了解决采场顶板安全问题和提高落矿主要技术经济指标而进行了“上向水平分层尾砂胶结充填法采场控制爆破技术”的试验研究工作,试验达到了预期效果。     

球墨铸铁材料对激光的吸收率

球墨铸铁因其优良性能而被广泛用作模具材料。对球墨铸铁冲压模具的激光表面处理已成为改善其耐磨性、提高使用寿命的重要方法。一定激光参量下吸收率的大小又直接影响到表面处理的质量。因此,确定球墨铸铁材料对激光的吸收率十分必要。通过热电偶测温,计算机数据采集系统进行定点温度采集,并结合数值模拟方法,对吸收率进行了标定,即首先根据预置的吸收率计算,预测被测点处的温度响应,并与实测响应比较,不断修正吸收率值,使预测温度响应和实验值吻合,由此获得吸收率。采用这种方法获得了球墨铸铁材料在大气条件下对激光的吸收率为23.3%。为激光处理球墨铸铁材料时工艺参量的选择和优化提供了一定参考。     

The use of the stable isotope 44Ca in studies of calcium incorporation into dentin

The incorporation into rat incisor dentin of two calcium isotopes, the stable ⁴⁴Ca and the radioactive ⁴⁵Ca, was studied using secondary ion mass spectrometry (SIMS) stepscanning and imaging, and autoradiography, respectively. The results demonstrated a time-dependent incorporation of the calcium isotopes into the mineral phase of dentin. With the SIMS step-scanning, detecting ⁴⁴Ca, the ion yield was high in the odontoblasts 2 min after intravenous injection. After 10 min a marked increase in signal intensity was found at the dentin mineralization front. This result was consistent with those obtained by ⁴⁵Ca autoradiography; a peak of incorporation occurred 10 min after injection of the isotope. Likewise, localization of ⁴⁴Ca to the mineralization front could be demonstrated 10 min after injection by SIMS imaging. In images obtained at earlier intervals, no such increase in ion yield could be detected. The results show that the nonradioactive, stable isotope ⁴⁴Ca can be used as a marker for biomineralization in a similar way to radioactive ⁴⁵Ca.     

Development and implementation of a NURBS curve motion interpolator

This paper deals with the issues of development and implementation of a real-time NURBS interpolator for a six-axis robot. Using an open-architecture controller system as a testbed, a real-time NURBS curve interpolator was developed, implemented and tested. Sample runs were conducted with the resulting trajectories measured in real-time during robot motion. The resulting trajectories are analyzed, discussed and compared with those from a commonly used point-to-point approximation technique. The real-time NURBS curve interpolator's feasibility, advantages and related issues are also discussed.