Mechanical behaviour of a combined joint composed of mechanical fastening and adhesive bonding

A study has been made of ‘combined’ joints consisting of mechanical fastening and adhesive bonding between rigid adherends. The mechanical characteristics of such ‘hybrid’ butt and lap shear joints have been derived by theoretical analysis. Results from experimental tests in combined joints giver reasonable agreement with the theoretical equations relating joint load to deformation.     

Effect of particle size on the surface oxidation and flotation behavior of galena particles in lime system

ABSTRACT

In this research, the effect of particle size on the surface oxidation and flotation behavior of galena in the lime system was studied. Coarse (?0.074 + 0.038 mm), intermediate (?0.038 + 0.025 mm) and fine (?0.025 mm) galena particles were used in the experiment. The dissolution tests, flotation tests, and sorption tests were accomplished. Through further analysis by XPS, the effect of particle size and lime was observed. The decrease of mineral particle sizes increased the adsorption ratio of collector and the dissolution of galena, while the hydrophilic product OH^?/Ca(OH)⁺ produced by dissolution occupied the dominant position, which led to the minerals hydrophilic.     

碳纤维经氧等离子/KH550处理后的表面形态和结构

碳纤维(CF)表面经氧等离子、KH550和 LiAlH_4处理后,其物理和化学性能得以改善.由于提高了 CF 和树脂间的联结,使 CF 复合材料的层间剪切强度提高50%以上,在湿热下的强度保留率达94%以上.使用纤维接触角测定仪,SEM 和 XPS 等对 CF 表面的浸润性、形态和化学组成进行了研究.实验指出:CF 经等离子和 KH550处理后,其临界表面能有了提高;CF 本身仅受氧离子刻蚀,故其拉伸强度的损失小于其他处理方法.     

基于GPGPU的实体表面实时提取

为实时提取三维实体表面,提出一种基于GPGPU并行计算的实体表面实时提取方法。在分析深度剥离算法原理和GPU图形绘制管线的基础上,给出在GPU上利用深度剥离算法实现实时提取三维实体表面的算法;通过OpenGL的高级着色语言GLSL控制GPU的图形绘制管线实现了该算法,给出其伪代码。以龙、叶轮和刀具扫描体的模型为应用实例验证了该算法效果良好,特别是对于刀具扫描体表面的提取,可满足实时性要求。     

硅压阻式气压高度计的设计与实现

采用硅压阻式压力传感器,以ATmega88PA为控制器设计了气压高度计。内嵌全温度范围的曲面拟合算法进行温度补偿及线性化处理,解决了压力传感器的温漂和非线性问题,并用海拔高度与气压的关系计算高度。测量结果通过RS-485接口发送给上位机。测试结果表明,该气压高度计压力测量误差优于0.50‰,分辨率为0.01 h Pa,线性度为0.999 9;标准大气环境下高度测量误差为0.16 m,线性度为0.999 8。该气压高度计具有质量小、功耗低、精度高、工作可靠等优点。     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

应力型微悬臂梁生化传感器响应机理研究进展

针对静态微悬臂梁表面特异性结合产生表面应力信号的响应机制问题,介绍了微悬臂梁生化传感器的工作原理,阐述了应力响应机制的简化模型,从纵向界面上和横向分子间2个方面对特异性吸附引起的悬臂梁表面应力的变化进行了剖析,讨论了界面能变化、位阻作用、静电力、氢键作用等与表面应力大小及方向之间的关系,总结了应力型微悬臂梁生化传感器的响应机理的研究。     

无线无源声表面波传感器研究进展

声表面波（SAW）传感器是一种无线无源传感器,在无源传感、适应恶劣环境等许多方面具有普通传感器不能实现的优点.阐述了声表面波器件的原理和结构特点,并对射频信号收发、信息处理等关键技术进行详细论述,综述了近些年国内外的相关研究现状,并进行了总结与展望.     

基于表面等离子体共振传感器的尿微量白蛋白检测

检测尿微量白蛋白(MAU)可对轻微肾脏损害进行早期诊断,也可对高血压患者可能发生的心脑血管事件进行预测。实验将抗体通过巯基自组装固定于Au膜表面,研制了一种快速检测MAU的表面等离子体共振(SPR)生物传感器。结果表明:直接检测法可以检测到0.3μg/L的MAU,而纳米Au放大法检测限可以低至0.03μg/L。