低掺杂浓度Nd:YVO4激光器的输出特性研究

在对Nd:YVO_4晶体的掺杂浓度和晶体长度对激光器性能的影响进行了分析后,报道了利用掺杂浓度为0.3at％,通光长度为10mm的Nd:YVO_4晶体作为增益介质,带光纤耦合的激光二极管端面抽运的Nd:YVO_4激光器。在抽运功率为27.365W时,获得了14.85W的TEM_(00)模输出,光一光转换效率为60.49％,斜效率达64.5％。     

泥沙悬浮的特征长度和悬移质浓度垂线分布

通过对紊动水流中混合掺长概念的类比,本文引入了泥沙作悬浮运动的特征长度的概念并讨论了其表达式的确定方法,从而在未经引入任何流速分布公式的情况下得到了一个悬移质浓度分布的统一公式,几乎所有已有各家公式均为本公式的特例。本文所采用的方法具有许多优点,采用本文的有关结果也便于从统一的高度来分析以往类似公式之间的内在联系、各公式的合理性及局限性。     

挖掘机工作装置实验样本长度确定方法及程序系统

本文通过对某液压挖掘机工作装置实验样本长度的研究,详细讨论了样本长度的确定方法,重点分析了趋势曲线拟合法,提出了样本长度精度区间分析的方法,并在处理大量实验数据的基础上,从载荷分布及寿命估算的角度做了实际的验证.编制了应用程序,使样本长度确定至寿命估算整个过程程序化.     

Construction of transmission lines above valuable standing timber

Problems with the construction of transmission lines above a forest are examined. Construction of lines above standing timber makes it possible to shorten the length of the route, eliminate the clearing of a continuous swath along the line, and reduce the volume of in-service work. To implement this solution, it is necessary to introduce changes and supplements to existing regulatory technical documents. __________ Translated from élektricheskie Stantsii, No. 10, October 2007, pp. 48–51.     

光纤光栅的长度对其峰值反射率的影响

利用耦合模理论,数值分析了当光纤光栅(FBG)折射率变化为均匀分布、直流切趾高斯分布时,光纤光栅长度对其峰值反射率的影响。研究结果对光纤光栅外腔半导体激光器的设计和性能优化具有重要的意义。     

塑料布"V"形铺设法在水库引冰爬坡中的应用

通过塑料布“Ｖ”形铺设法在胜利水库引冰爬坡的应用与实践，证明了此法与传统贴坡式塑料布铺设法相 比，大大削减了冰推力对坝坡的破坏，减少了坝坡的修复费用，起到了良好的效果。     

Alternating,all-trans polyenynes: Model compounds for poly(diacetylene)s with defined conjugation length

The syntheses of polyenynes as model compounds for poly(diacetylene)s (PDAs) are described. Variation of properties (UV–VIS, Raman, NMR and bond geometries) as a function of the chain length was investigated. After extrapolation to infinite chain length these data were compared to those for PDAs. From UV–VIS spectra a value of λ = 551 nm (2.25 eV) was calculated corresponding to the electronic transition of a single polyenyne chain. This energy is located at the low energy end of a yellow PDA solution spectrum. From Raman scattering v_(C?C) = 2108–2128 cm^?1 and v_(C?C) = 1505–1532 cm^?1 were calculated after extrapolation. Similarly sp-C¹³C NMR data yielded a shift of δ = 100 ppm. These data are almost identical to data known for yellow PDA solutions. Bond geometries are almost identical to those of poly(diacetylene)s and theoretical data.     

定向爆破拆除高危烟囱的实践

通过对已产生纵向裂缝、倾斜和基部风化剥蚀严重的高危烟囱的定向（向倾斜相反方向）倒塌爆破实践表明：设计中选用爆破参数及施工措施是有效的。     

Machining with tool–chip contact on the tool secondary rake face—Part II: analysis and discussion

The forces, chip thickness, and natural tool–chip contact length in machining with a double-rake-angled tool are predicted in Part II of the present study. It is revealed that in comparison with a single-rake-angled tool, a double-rake-angled tool increases the forces, especially the thrust force. However, the increase in chip thickness and tool–chip contact length is not significant under the input conditions specified in the present study. The effect of seven input variables of the proposed model is quantitatively investigated. The predicted variations of forces, chip thickness, and natural tool–chip contact length are in good agreement with theoretical and experimental results obtained by other researchers. The interrelationships among the resultant force, the chip thickness, and the natural tool–chip contact length are established, which provides a new and promising method to estimate the tool–chip contact length by employing the resultant force. It is demonstrated that the model can also be extended to study the problem of machining with a groove-type chip breaker tool.