Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Discrete-time spare ordering policy with randomized lead times and discounting

The paper considers a generalized discrete‐time order‐replacement model for a single unit system, which is subject to random failure when in operation. Two types of discrete randomized lead times are considered for a spare unit; one is for regular (preventive) order and another is for expedited (emergency) order. The model is formulated based on the discounted cost criterion. The underlying two‐dimensional optimization problem is reduced to a simple one‐dimensional one and then the optimal ordering policy for the spare unit is characterized under two extreme conditions: (i) unlimited inventory time and (ii) zero inventory time for the spare unit. A numerical example is used to determine the optimal spare‐ordering policy numerically and to examine the sensitivity of the model parameters.     

Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.     

Turbo码中快速交织器的设计

分析了交织器在Ｔｕｒｂｏ码中的重要作用，以及目前交织器存在的缺陷，介绍了一种快速交织器的设计方法。该交织器易于实现，具有交织时延低的突出优点。计算机仿真结果表明，该快速交织器可以获得优异的性能。     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

安徽省长江干堤的几种加固措施

安徽省境内765km的长江干堤，由于均是在原来旧堤的基础上经逐年加高培厚的，修筑时均未按设计要求施工，致使堤身密实度不够，新老堤土之间结合不牢，在汛期高水位时易产生渗漏。20世纪70年代以来，安徽省高度重视对长江干堤渗漏隐患的处理，经过长期的实践，逐渐摸索出一套行之有效的除险加固方法，如锥探灌浆、灭杀白蚁、冲抓套吉、垂直铺塑防渗、粘土铺盖及压渗盖重等处理措施。使长江干堤的渗漏隐患得以基本消除，其具体作法可供类似工程借鉴。     

Determination of instantaneous corrosion rates and runoff rates of copper from naturally patinated copper during continuous rain events

Instantaneous corrosion rates of naturally patinated copper of varying age (16 months, 138 and 145 years) have been determined during continuous rain events in the laboratory with electrochemical impedance spectroscopy using a two-electrode cell. The two-electrode cell was found to yield the same information in bulk rainwater as a conventional three-electrode cell.Relatively constant corrosion rates, between 0.2 and 0.6 μm/y, were determined for samples having a two-layer structure with an inner brownish layer of cuprous oxide and an outer greenish layer of basic copper salts (138, 145 years). Samples with cuprous oxide as the dominating phase of the patina (16 months) showed higher and somewhat increasing corrosion rates during a rain event (from 0.6 to 1.2 μm/y). During a continuous rain event, corrosion rates were found to be approximately 10 (brownish patina) and 25 times (greenish patina) lower than corresponding instantaneous runoff rates. The first flush phenomena of the runoff process, with an increased concentration during first flush and a relatively constant concentration during steady state, was indirectly seen as an increase in solution conductivity during the first rain volume followed by relative constant value. The contribution of the concentration in the first flush to the total annual runoff rate was significant for panels having a greenish layer (138, 145 years) whereas it was negligible for panels having a brownish layer (16 months).     

化工离心泵的可靠性分析

对石油化工设备安全性和维修技术的研究,需要设备运行故障率等可靠性数据。探讨了如何应用传统可靠性理论知识,并结合国内外相关标准规范和运行数据的统计分析来确定离心泵的可靠性数据的方法。     

轴向进给比对薄壁管滚珠旋压影响的有限元分析

通过有限元数值模拟方法得出滚珠旋压中薄壁管在不同凹模旋转速度条件下轴向进给比的变化规律及工件的成形规律,并对模拟结果的等效应变分布做了分析,并与实验结果进行比较,给出薄壁管滚珠旋压时进给比的选取范围.结果表明,进给比对滚珠旋压中薄壁管直径的胀缩和工件的质量有着显著的影响.另外,从计算的模具所受的三向载荷变化情况分析了模具的使用寿命.     

新《企业会计准则》中实际利率法的应用

2006年2月15日财政部颁布的《企业会计准则》中有多处要求采用实际利率法计算摊余成本和利息，而会计职称考试用书等资料则采用列表形式。本文在分析实际利率法内涵的基础上，通过若干实例解析了利用账簿记录计算各期摊余成本。