强度调制／直接检测（IM／DD）光纤通信系统色散限制的研究

通过引入归一化脉宽Ｐ和相对脉冲展宽因子ｑ，提出了一个适用于ＩＭ／ＤＤ系统中各种眼图恶化量ｘ和归一化脉宽Ｐ的色散限制改进公式。通过与其它理论的比较、计算机仿真和对实验数据的分析，验证了该公式的正确性，并给出了其它结果的限制条件。研究表明：当眼图恶化量ｘ为１ｄＢ左右时，对２．５Ｇｂ／；外调制信号（α＝０）而言，非色散位移光纤ＩＭ／ＤＤ系统的色散因子γ约等于０．７９，所对应的系统再生中继距离约为９００余公里。     

高效防气防砂一体化管柱的研制与应用

为解决文南油田高气液比井出砂易造成卡泵的问题,研制了高效防气防砂一体化管柱。该管柱主要由闭式气锚、重力式防气装置和激光割缝筛管3部分组成。闭式气锚的分离作用消除了气体对抽油泵的影响,提高了泵效;重力防气装置利用液气分离原理和高烟囱原理进行液气分离,液流回流时间可达10min,排气最高压差可达0.2MPa;经激光割缝筛管过滤后的液体含砂粒外径小于0.05mm。该管柱在文南油田现场应用16井次,累计增液6000t,增油2717t,平均单井泵效提高7%。     

用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。     

On the hollowness ratio effect on the dynamics of a spinning Rayleigh beam

The analytical solutions of a spinning Rayleigh beam with rotatory moment inertia and gyroscopic effect are presented in this paper. The critical speeds can be written analytically in a function of the length-to-radius ratio (l) defined by the beam's length over its outer radius and the hollowness ratio (α) defined by the hollow area over the total area of the cross section. The sensitivity analyses show that the critical speed is decreasing with l, but increasing with α. Moreover, α is more sensitive to the critical speeds. The design of a spinning beam should therefore be emphasized more on the hollowness factor. Contrary to common belief, only finite critical speeds exist and the number is independent of the boundary conditions. It increases monotonically with l, but decreases with α. The steady state unbalanced response can therefore be expressed analytically by the finite precessional modes and the corresponding generalized coordinates.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Sensitivity analysis of initial value problems with mixed odes and algebraic equations

An efficient method is described for sensitivity analysis of nonlinear initial value problems, which may include algebraic equations as well as ordinary differential equations.The linearity of the sensitivity equations is utilized to solve them directly via the local Jacobian of the state equations. The method is implemented with the implicit integrator DASSL and is demonstrated on a stiff industrial reaction model.     

降低氧化铝生产中熟料折合比的探讨

在氧化铝生产过程中，熟料折合比是烧结法一项重要的综合性指标，本文通过对熟料折合比的定义、计算公式的剖析，分析了生产过程中影响熟料折合比的主要因素，对有效降低熟料折合比的措施进行了探讨。     

étude des rechutes constatés dans une cohorte de personnes jugées inptes à subir leur procés ou acquittées pour cause d'aliénation mentale.

[Correction Notice: An erratum for this article was reported in Vol 20(2) of Canadian Journal of Behavioural Science Revue canadienne des Sciences du comportement (see record 2007-09831-001). The abstract accompanying the original article was incorrect; the correct abstract (in French) is presented in the erratum.] We know little about individuals who are declared unfit to stand trial and/or not guilty by reason of insanity. The few existing studies are characterized by methodological weaknesses, notably by short follow-up periods and a lack of external validity. The present investigation, which aims to evaluate and explain readmissions that occurred during a seven- to nine-year period, corrects only some of these weaknesses. Sixty-one per cent of the subjects were rehospitalized during the period of study. It proved difficult to identify the factors associated with readmission. However, males with a diagnosis of schizophrenia and who had committed violent crimes were found the most likely to be readmitted. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A motivational model of rural students' intentions to persist in, versus drop out of, high school.

Using self-determination theory, the authors tested a motivational model to explain the conditions under which rural students formulate their intentions to persist in, versus drop out of, high school. The model argues that motivational variables underlie students' intentions to drop out and that students' motivation can be either supported in the classroom by autonomy-supportive teachers or frustrated by controlling teachers. LISREL analyses of questionnaire data from 483 rural high school students showed that the provision of autonomy support within classrooms predicted students' self-determined motivation and perceived competence. These motivational resources, in turn, predicted students' intentions to persist, versus drop out, and they did so even after controlling for the effect of achievement. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

可焊性高强度钢筋的开发与生产

为进一步开发国际钢材市场，研制开发了符合加拿大可焊性高强度钢筋标准要求的高强度钢筋．制定了化学成分及力学性能内控标准，分析了生产工艺各环节对成分和性能的影响，依据试验结果，在全面统计分析的基础上，调整了冶炼成分，生产的531批钢筋全部合格．通过直方图及回归分析，说明了制定的产品生产工艺可行，也为今后的生产提供了理论依据。