商品混凝土降低成本的技术途径

商品混凝土目前价格偏高 ,用户不情愿接受 ,影响了它的推广应用。针对这一问题 ,本文提出了用“活化填料”、“活化水泥”配制高性能商品混凝土的技术路线并分析了其技术经济效益     

金属矿山深热矿井空气温度的灰色预测

金属矿山深热矿井气温的预测计算是一个难题，本文探讨了应用灰色系统预测理论来解决这一难题的新途径，并通过实例验证了该方法的可行性和有效性。     

高炉加入含钛物料护炉的方法探讨

比较分析了目前高炉所采用的两种加入含钛物料护炉的方法，长期少量均匀加入法和间断大量加入法，并结合梅山１号高炉折护炉实践和停炉后的破坏调查结果，提出了第三种加入含钛物料的方法，即长期适量加入法。     

Air entrainment in fresh concrete with PFA

The results of a study into the influence of PFA on air entrainment in fresh concrete are discussed It is shown that the required dosage of AEA to produce an air content of 5.5 ± 0.5% in a PFA modified concrete mix is two-six times that required in the corresponding neat OPC concrete mix. The dosage of a vinsol based air entraining agent (AEA) required appears to be directly related to the PFA content of the mix. Similar direct relationships were obtained with a range of different PFAs. The dosage of an AEA based on the salt of a fatty acid appears to be sensitive to both PFA and OPC contents. For the type of PFA used, the variability of measured air content or the amount of air retained after continued agitation both indicated that vinsol based AEAs show the highest variability whilst fatty acid based AEAs show low variability. The between batch variability of air content was significantly improved by the addition of PFA regardless of the AEA used.     

微波场中光纤探头温升的研究

当把光纤温度传感器置于微波场中测温时，由于受电磁场的作用，传感头内部将有能量损耗，以致发生测温偏差。本文将传感头简化成有限长圆柱，计算出在微波场中传感头的能量损耗和温度变化。最后还分析了一种实际热色效应光纤温度传感器。     

新型模具钢012Al在深冷处理过程中的组织转变

本文利用x-射线衍射分析及复型和薄膜透射技术研究了012Al钢经淬火后在深冷处理过程中的组织转变。结果表明,淬火后的残余奥氏体在深冷处理过程中部分转变成马氏体;深冷处理使马氏体发生分解,析出超细碳化物;同时伴有形变晶孪产生。     

型钢厂试轧美标H型钢性能分析研究

分析了型钢厂试制热轧美标H型钢低温冲击韧性偏低的原因，并在此基础上提出了对生产工艺的优化与改进。     

Heat loss and thermoelectric generator design

With the object of evaluating its importance to thermoelectric generator design, heat loss is introduced into the standard thermoelectric generator design theory. The theory for both the constant hot and cold junction temperatures model and the constant heat input model are so modified. The modification is first order and, therefore, is limited to small leg heat-transfer coefficients. Numerical results using representative properties show that significant differences can exist between the optimum geometry and performance of a generator idealized as lossless and those of a generator designed by the modified theory. The largest differences occur with the constant heat input model.     

现浇混凝土构件与砌体接触面收缩和温度应力裂纹的探讨

分析讨论了建筑物由于收缩及温度应力而引起的过纹，提出了在设计施工中应考虑的问题和采取的防止措施。