机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

无机阻燃剂高聚合度聚磷酸铵的研制

以五氧化二磷、磷酸铵盐、尿素为原料、氨气为保护气,制备了高聚合度聚磷酸铵无机阻燃剂。考察了五氧化二磷、磷酸铵盐、尿素的用量和反应温度对聚磷酸铵平均聚合度的影响。采用端基滴定法测定了聚磷酸铵的聚合度,并用X射线衍射(XRD)法表征了聚磷酸铵的晶体结构,同时测定了聚磷酸铵的粒度和溶解度。实验结果表明,制备聚磷酸铵的最佳反应条件为:n(磷酸氢二铵)∶n(五氧化二磷)∶n(尿素)=1∶1∶0.3,反应温度280~300℃,反应时间40m in,热处理温度250~280℃,热处理时间110m in。在此条件下制备的聚磷酸铵的平均聚合度大于600,平均粒径直径小于50μm,在水中的溶解度小于0.4g;XRD表征结果表明,所合成的物质为Ⅱ型聚磷酸铵。     

Anthocyanin composition of the red wine Babić affected by maceration treatment

Identification of anthocyanins in the wine made of the Croatian autochthonous grape variety of Babić (Vitis vinifera L.) was carried out and their profile was determined by means of high-performance liquid chromatography with diode array and mass spectrometric detection. Dependence of anthocyanins content and profile on maceration treatment conditions was investigated. Statistically significant differences of anthocyanins concentration in wines Babić produced by various maceration treatments were confirmed by the use of multivariate analysis of variances. The investigation results indicated that the maceration temperature exerts higher influence on anthocyanins concentration than the duration of maceration. In addition, on the basis of anthocyanin composition and using different multivariate statistical analyses, differentiation of wines Babić according to maceration treatments was procured.     

Phosphorus‐containing polyaryloxydiphenylsilanes with high flame retardance arising from a phosphorus–silicon synergistic effect

Polyaryloxydiphenylsilanes were prepared from phosphorus‐containing diols and diphenydichlorolsilane through solution polymerization. With a stoichiometric imbalance in feed monomers, the resulting polymers exhibited moderate melting points and good processing properties. The polymers prepared showed initial decomposition temperatures above 340 °C, excellent thermal stability, high char yields at 850 °C and very high limited oxygen index values of 56–59. The polymers' char yields and their (P + Si) contents showed linear relationships. © 2003 Society of Chemical Industry     

带通采样在数据采集中的应用研究

在数据采集中采用带通采样，可大大降低采样率，但系统中的抗混叠滤波器会造成相位的非线性。采用对滤波后的信号进行带通采样，然后再用FRR滤波器校正相位的非线性，从而不失真地还原原信号，最后在Matlab中进行仿真，验证了该方法的有效性。     

聚合物分散液晶(PMMA:5CB:C60)光折变特性的实验研究

用溶致相分离方法制备了3种不同组分的聚合物分散液晶薄膜(PMMA：5CB：C60)，C60作为敏化剂。利用二波耦合实验测量了不同样品的衍射效率和响应时间等光折变特性，实验发现，液晶含量不同的薄膜光学性质有很大的不同。     

Thermodynamic and Transport Properties of Liquid HFC-227ea

The thermal conductivity and heat capacity of liquid 1,1,1,2,3,3,3-hepta-fluoropropane (HFC-227ea) have been studied by a high-frequency thermal-wave method over the temperature range of 294 to 345 K at pressures up to 2.8 MPa. The purity of the samples used throughout the measurements is 99.99 mol%. The experimental uncertainties of the thermal conductivity and heat capacity measurements were estimated to be within ±1.5 and ±2%, respectively. The thermal conductivity of HFC-227ea in the liquid phase decreases as temperature increases, while the pressure has an opposite effect.     

Phase behavior,density, and crystallization of polyethylene in n‐pentane and in n‐pentane/CO2 at high pressures

The phase behavior and volumetric properties of polyethylene (PE) in solutions of n‐pentane and n‐pentane/CO₂ were studied in a temperature (T) range of 370–440 K at pressures up to 60 MPa. Measurements were conducted with a variable‐volume view‐cell system equipped with optical sensors to monitor the changes in the transmitted light intensity as the P or the T of the system was changed. Lower‐critical‐solution‐temperature‐type behavior was observed for all of the liquid–liquid (L–L) phase boundaries, which shifted to higher pressures in solutions containing CO₂. The solid–fluid (S–F) phase boundaries were investigated over a P range of 8–54 MPa and took place in a narrow T range, from 374 to 378 K in this P interval. The S–F phase boundary showed a unique feature in that the demixing temperatures showed both increasing and decreasing trends with P depending on the P range. This was observed in both the PE/n‐pentane and PE/n‐pentane/CO₂ mixtures. The density of these solutions were measured as a function of P at selected temperatures or as a function of T at selected pressures that corresponded to the paths followed in approaching the phase boundaries (S–F or L–L) starting from a homogeneous one‐phase condition. The data showed a smooth variation of the overall mixture density along these paths. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2201–2209, 2003     

Dynamics of liquid-filled spacecraft

A method is presented for simulating coupled liquid-solid dynamics. An important example of a coupled liquid-solid system is a satellite carrying fuel. The dynamics of the satellite and the onboard fuel influence each other, which may lead to satellite motion that is uncontrollable. For better understanding of the complex dynamics of coupled systems, a numerical model is developed. The model consists of two parts. The first part that solves the liquid motion is only briefly discussed here. The focus in this paper is on the way in which the dynamics of the liquid and the solid body are coupled. For this, the governing equations are presented in which terms appear that represent the force and torque on the solid body due to the sloshing liquid. The governing equations are rewritten such that the discrete approximation of these equations can be integrated in a stable manner for arbitrary liquid/solid mass ratios. Results are presented demonstrating the stability of the present model. A grid-refinement study and a time-step analysis are performed. Finally, the flat-spin motion of a satellite, partially filled with liquid, that flew in 1992 as part of the Wet Satellite Model experiment is studied. Results from the simulation are compared with the actual flight data.     

液态金属离子源发射尖的制备工艺与技术

发射尖是液态金属离子源(LMIS)的关键部件之一，其性能的优劣直接影响到整个离子源的工作稳定性。通过对系统软件和硬件的设计，开发了一套发射尖自动腐蚀装置，该装置可以对发射尖腐蚀过程中的速度和深度以及腐蚀电压进行控制，实现发射尖腐蚀工艺的重复性、可靠性，从而为液态金属离子源以及聚焦离子束系统的研制、开发提供了一个有效的辅助工具。