湿陷性黄土地区几种地基处理方法的比较

通过一工程实例,介绍了在湿陷性黄土地区几种地基处理方法的应用,并从技术、经济、施工进度等方面进行了分析比较,可供土建设计人员借鉴、参考。     

镁热还原法制备超微细无定形硼粉

以B2O3为原料,Mg粉为还原剂,通过自蔓延镁热还原反应获得还原产物,经过对还原产物的盐酸溶浸后,制备出超微细无定形硼粉.研究镁热还原工艺对产物的影响,利用激光粒度分析仪测定无定形硼粉的粒径,用静态表面吸附仪测定77.3 K下硼粉的氮吸附等温曲线,通过XRD和SEM分别对还原产物和无定形硼粉的物相及形貌进行分析.结果表明在B2O3-Mg体系中,影响硼粉纯度的杂质主要是反应过程中生成的酸不溶物MgBx、BxO、Mg2SiO4、FeBx及较难溶物xMgO.B2O3等,在镁热还原过程中应尽量抑制该类化合物的生成.通过优化制备工艺,在w(B2O3)/w(Mg)为3.0的条件下,制备出硼含量为94.6%、比表面积8.2 m2/g、等效粒径0.36 μm的形貌不规则的超微细硼粉.     

细菌纤维素合成过程中的影响因素

研究了接种量、pH值、培养液深度、培养液表面积和发酵时间等因素对形成细菌纤维素膜的产量、厚度及比表面积的影响。结果表明:接种量在7%、初始pH值在5～6范围内细菌纤维素的产量最大;厚度主要取决于发酵时间和初始pH值;培养液表面积对单位面积细菌纤维素产量有比较大的影响;膜的比表面积与发酵时间的长短无关。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

气相法二氧化硅应用机理及特性

主要介绍了气相法二氧化硅在液态体系、干燥体系、固态体系中的作用机理；气相法二氧化硅在应用中的特殊性能；以及比表面积、pH、含水量、添加量、表面处理程度等气相法二氧化硅各项物理性能对应用性能的影响。     

Silicon Nitride Derived from an Organometallic Polymeric Precursor: Preparation and Characterization

Partially crystalline Si₃N₄, with nanosized crystals and a specific surface area greater than 200 m²/g, is obtained by pyrolysis of a commercially available vinylic polysilane in a stream of anhydrous NH₃ to 1000°C. This polymer does not contain N initially. Crystallization to high-purity α-Si₃N₄ proceeds with additional heating above 1400°C under N₂. The changes in crystallinity, powder morphology, infrared spectra, and elemental compositions, for samples annealed from 1000° to 1600°C under N₂, are consistent with an amorphous-to-crystalline transformation. Although macroscopic consolidation and local densification occur at 1400°C, volatilization and accompanying weight loss limit bulk densification. The effect of temperature on specific surface area is examined and related to the sintering process. These results are applicable to pyrolysis, decomposition, and crystallization studies of ceramics synthesized by polymeric precursor routes.     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

Influence of Carbon on SOx Emissions from Glass Processing

Carbon reacts with Na₂SO₄ in glass batches, influencing SO _x emissions. To study the role of carbon active surface area (ASA) in the decomposition phenomena, Na₂SO₄ is reacted with three carbons with a wide ASA range. The decomposition behavior was evaluated by thermogravimetric analysis (TGA) and evolved gas analysis via mass spectrometry and Fourier transform infrared spectrometry. Higher carbon ASA yields lower decomposition temperatures. SO _x emissions are realized at temperatures as low as 773 K. Isothermal Na₂SO₄–C decomposition initiates via the nucleation of Na₂S. The rate constants for the nucleation regime are normalized against ASA, yielding an activation energy of 275 kJ/mol for nucleation.