Preparation of molecularly imprinted fluorescence sensor based on carbon quantum dots via precipitation polymerization for fluorescence detection of tetracycline

A facile and effective method was proposed to prepare the molecularly imprinted fluorescence sensor with carbon quantum dots, which were modified vinyl groups by acrylic acid on the surface. The obtained fluorescence composite material was investigated by transmission electron microscope and Fourier transform infrared spectra. After the experimental conditions were optimized, a linear range of 1.0–60 μmol L⁻¹ was obtained and the detection limit was 0.17 μmol L⁻¹. The novel fluorescence sensor can be successfully used to detect tetracycline in real samples. This study provides a convenient strategy for selective recognition and rapid detection of tetracycline in the complex environment.     

An iterative method for suboptimal control of linear time-delayed systems

This article presents a new approach for solving the Optimal Control Problem (OCP) of linear time-delay systems with a quadratic cost functional. The proposed method can also be used for designing optimal control time-delay systems with disturbance. In this study, the Variational Iteration Method (VIM) is employed to convert the original Time-Delay Optimal Control Problem (TDOCP) into a sequence of nonhomogeneous linear two-point boundary value problems (TPBVPs). The optimal control law obtained consists of an accurate linear feedback term and a nonlinear compensation term which is the limit of an adjoint vector sequence. The feedback term is determined by solving Riccati matrix differential equation. By using the finite-step iteration of a nonlinear compensation sequence, we can obtain a suboptimal control law. Finally, Illustrative examples are included to demonstrate the validity and applicability of the technique.     

最大塑性功原理在烧结体上限分析中的应用

最大塑性功原理又称第二塑性变分原理，在致密体塑性变形分析叶l是运用能量法进行变形力能计算的基础。本文从分析Drucker公设的亢要条件出发，证明了烧结体塑性变形最大塑性功原理的存在，片在该原理的荩础卜，推导出塑性变形的上限功率表达式，并以平面挤压条件下的上限法应用作为实例加以说明。     

A note on the value function for constrained control problems

We consider the Mayer optimal control problem with dynamics given by a nonconvex differential inclusion, whose trajectories are constrained to a given set and we obtain a relation between the costate function that appears in the maximum principle and the value function. This relation extends the known conditions existing in the literature for unconstrained problems to those for problems under state constraints.     

二氧化碳加氢直接合成二甲醚催化剂的研究——沉淀次序对复合催化剂结构和性能的影响

以草酸乙醇溶液为沉淀剂,采用不同的沉淀次序(并流、反加和正加)制备了CuO-ZnO-Al2O3/HZSM-5复合型催化剂,对CO2加氢直接合成二甲醚反应的催化活性顺序为:并流法催化剂>反加法催化剂>正加法催化剂。3种复合催化剂的还原温度由低到高的顺序为:并流法催化剂<反加法催化剂<正加法催化剂。在沉淀过程中,反加法和正加法均形成类胶体沉淀,相应催化剂的比表面积也较大。IR研究发现,催化剂在1101cm-1处表现Cu/Zn/Al氧化物与HZSM-5分子筛之间相互作用的IR吸收峰强度与其催化活性间存在对应关系。XRD结果表明,并流法得到的催化剂前驱体中有铜锌同形取代现象,有利于催化剂活性的发挥。     

动力环境网络监控精细管理

叙述动力环境运行质量分析管理，包括故障管理，性能管理和专题分析管理，以动力环境网络监控细致八微、言之有据的月度分析管理实例展现了其精细管理的效果。     

Taxometrics in Psychopathology Research: An Introduction to Some of the Procedures and Related Methodological Issues.

This article introduces a special section on the use of taxometrics to examine the categorical versus the dimensional structure of various forms of psychopathology. Paving the way into the special section, this introduction briefly describes 3 taxometric methods--mean above minus below a sliding cut (MAMBAC), maximum covariation (MAXCOV), and maximum eigenvalue (MAXEIG)--and discusses possible threats to statistical conclusion validity that often emerge when such techniques are applied in psychopathology research. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

小波变换在光谱特征提取方面的应用

人们在处理高光谱图像时一般要对一些典型地物进行光谱分析、特征波段的提取,以便提取出最大量的有效信息,剔除无用或冗余的信息,然后再进行分类识别.采用小波变换的分析方法,选用合适的小波进行分解,根据分解后的高频分量中包含的重要信息,利用局部相邻的正负极值点找出对应于原始光谱曲线上每个吸收带的左右边界;利用局部过零点,即可比较精确的提取出各个吸收带的中心波长.该方法比传统的光谱特征提取方法更简洁、有效,实验证明为一种比较理想的光谱特征提取方法.     

连续波雷达测距中的解模糊技术

研究连续波雷达测距中的距离模糊问题，分析几种常用解模糊方法的性能，并讨论参差比的选取对测距范围的影响。     

MRC分集接收的MQAM在Nakagami信道上的性能分析

Nakagami信道是一种适应性较强的信道模型，MQAM(M-ary quadrature amplitude modulation)是一种频谱利用率较高的调制方式。在存在多径影响的无线通信环境中，最大比合并(maximum ratio combining)方式的分集接收是克服衰落的有效方法。本文利用适用范围更广的Nakagami信道模型，在多径衰落的情况下对最大比合并分集接收的MQAM系统误符号率性能作了分析。仿真结果对分析实际信道下具体系统的性能具有一定的参考价值。