Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响

主要研究了Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响。首先利用Formastor-F型膨胀仪测定了含Cr和不含Cr两种低碳钢的连续冷却转变(CCT)曲线,分析指出了Cr对连续退火工艺的潜在影响;然后采用Gleeble-3800热/力模拟试验机对两种钢的薄板试样进行了连续退火模拟实验,并通过拉伸试验测定了力学性能;最后采用金相、扫描电镜、X-射线衍射分析等技术考察分析了两种钢的显微组织。结果表明:含Cr的TRIP钢的组织比较细小,铁素体晶粒近似等轴分布;两种TRIP钢的残余奥氏体含量相近,但含Cr钢的残余奥氏体中的含碳量较高。分析认为这是由于含Cr钢在热轧阶段较易生成细小的组织,而在热处理阶段则抑制贝氏体的生成,最终获得稳定的残余奥氏体。     

18臂机械井径与磁法井径组合测井仪原理及应用

文章主要介绍了18臂机械井径与磁法井径组合测井仪的仪器结构、主要技术特性、测量原理及测井资料在油田中的应用。通过对测井资料的分析，阐述了该仪器在套损检测、补贴效果检查、射孔工程作业效果评价等方面的应用，为油田套管分析提供了可靠的保证。     

Preparation and Properties of Rare Earth Modified Carbon Black/Natural Rubber Composites

The oxides Eu, Ho, Er and Dy were used to prepare the hydroxides of rare earth modified carbon black. Then natural rubber latex （NRL） was added into the reactor. The system reacted at 85 ℃ with stirring for 1 h to prepare powdered HAF-Ln（OH）3/NR composites. The effects of the kind and content of Ln on the particle size distribution of P [ NR/HAF-Ln （OH）3 ] and mechanical properties of its vulcanizate were studied respectively. It is found that rare earth can help to get the powder of the composite, the product particle with a diameter less than 0.9mm will be get when the composites containing the compound of Ho, Er and Dy with dosage of 1.0, 1.0, O. 5 percent, respectively. The adding of Ln can improve the tensile strength and tear strength of the vulcanizate effectively, what＇s more, Er and Dy can decrease the permanent set of vulcanizate significantly. The SEM studies shows that P[ NR/HAF-Dy （OH）3 ] vulcanizate shows superior mechanical properties that depend primarily on the absence of free carbon black, the fine dispersion of carbon black in the rubber matrix and better polymer-filler interaction.     

A new approach to study organic solar cell using Lambert W-function

Organic photovoltaic solar cells bear an important potential of development in the search for low-cost modules for the production of domestic electricity. One of the main differences between inorganic and organic solar cells is that photo-excitation in these materials does not automatically lead to the generation of free charge carriers, but to bind electron–hole pairs (exciton) with a binding energy of about 0.4 eV. Till now various numerical methods using approximations have been reported to study different aspects of organic solar cells. For the first time an accurate method using Lambert W-function is presented to study different parameters of organic solar cells.     

Performance of natural‐fiber–plastic composites under stress for outdoor applications: Effect of moisture,temperature, and ultraviolet light exposure

The effects of moisture, temperature, and ultraviolet (UV) light on performance of natural‐fiber–plastic composites (NFPC) were assessed. We conducted short‐term tests in the laboratory and long‐term tests under natural exposure and measured changes in mechanical properties and color in samples of the composite. Chemical changes of the composite's materials were measured by X‐ray photoelectron spectroscopy to elucidate the mechanisms of chemical transformations on the material surface. Relative humidity highly affected the modulus of rupture (MOR) and the modulus of elasticity (MOE), and had a greater effect than temperature and UV exposure on performance of the composite. The lightness of the composite was increased by the UV effect in the short‐ and the long‐term tests. The X‐ray photoelectron spectroscopy (XPS) analysis suggested that the composite was protected by the UV absorber. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2570–2577, 2006     

Analysis of S-SEED''s characteristics in optical switch

This article introduces the basic structure of a symmetric self-electrooptic effect device （S-SEED）, and applies the Kirchoff＇ s current law and a purely equivalent capacitive model, to analyze S-SEED＇s switch characteristics. Linear approximation and N-segment approximation are utilized to obtain S-SEED＇s voltage-time （V-T） and characteristics. Theoretical analysis is verified by simulations, and the results demonstrate that the precision of S-SEED＇s switch time can satisfy the requirement in applications with linear approximation. Moreover, the simulations compare S-SEED＇s switch characteristics with different input powers and input contrast ratios, which reveal that increasing input contrast ratio is an effective way to improve S-SEED＇s switch characteristics.     

关于从旋涡炉渣回收铜的研究

介绍了用自然澄清法降低、回收旋涡炉渣中的铜的方法。该方法工艺简单。操作方便，不仅降低冶炼成本，同时提高了经济效益。     

热镀锌工艺对Ti-IF钢光整热镀锌板组织和性能的影响

在连续热镀锌线上研究了RTH带钢温度和光整延伸率对Ti—IF钢光整热镀锌板组织和性能的影响。试验表明，当RTH带钢温度在830℃以下时，成品铁素体晶粒度为10．0级，织构类型以{332}、{114}为主，随着带钢温度的进一步提高，热镀锌板的晶粒逐渐粗化，织构成为典型的{111}织构，且取向密度增加，r值随之提高，但当带钢温度在900℃以上时，织构又趋于无规则分布，r值显著降低；光整延伸率对Ti—IF钢光整热镀锌板力学性能的影响很大，随着光整延伸率的提高，屈服强度明显提高，n值明显降低，延伸率降低，抗拉强度变化较小，且光整延伸率对性能的影响与成品铁素体晶粒尺寸有关，成品晶粒越粗，光整延伸率的影响越大。因此对于Ti—IF钢光整热镀锌板而言，n、r值是一对矛盾体，在制订热镀锌工艺时，需根据使用条件的不同，对其n、r值进行综合考虑。     

多孔硅发光二极管的载流子传输特性研究

制备AI／多孔硅／c-Si／Al结构的多孔硅发光二极管，利用其I-V特性关系，以及在不同温度下其I-V特性的变化，结合多孔硅的特殊微结构及性质，分析了多孔硅发光二极管中载流子的产生和传输过程；通过比较其发光猝灭前后I-V特性的变化，解释了发光猝灭的原因。提出了如果在低电场下能够实现大量载流子在限制性Si微粒中复合．是提高多孔硅电致发光效率的一个途径。