Na2SiO3—KOH—（NaPO3）6溶液中Ti6Al4V微弧氧化陶瓷膜研究

用非平衡交流微弧氧化法于Na2SiO3-KOH-(NaPO3)6溶液中在Ti6Al4V表面形成氧化物陶瓷膜。分别用扫描电镜、电子探针及X射线衍射研究了陶瓷膜的组织形貌、元素分布和相组成。相对致密均匀的膜层主要由TiO2(钙钛矿相及金红石相)及非晶相组成。厚约20μm的膜可分为3层：过渡层、致密层与疏松层。电解液所含元素Si，P进入到膜层中，表明电解液组元急烈参与微弧氧化反应，这为通过选择电解液来设计膜层的相组成进而对膜层进一步改性提供途径。     

A New Process to Make a Porous PTFE Structure from Aqueous PTFE Dispersion with the Help of Hydrogel

A novel method to make a porous material having relatively large cell diameter (200–300 m), which consisted of mainly poly(tetrafluoroethylene) (PTFE), was developed from aqueous PTFE dispersion by using the characteristics of hydrogel with the addition of carbon nanofiber (CNF). The porous material was produced as follows: firstly, an aqueous agar gel containing PTFE and CNF was prepared; secondly, the gel was freeze-dried; thirdly, the dried gel was heat-treated at 400°C where the agar was almost decomposed and PTFE became molten. The porous material showed electric conductivity (about 50 ), high porosity (about 96 vol%), and relatively uniform cell structures without shrinkage during freeze drying and heat treatment. While the method without CNF resulted in large shrinkage during heat treatment, meaning that CNF prevented the shrinkage. It was explained by the idea that the existence of rigid CNF, which was dispersed in the cell wall, prohibited the shrinkage of PTFE during heat treatment. It was unexpectedly found by SEM analysis that the porous materials had another macro-porous structure inside the cell wall, suggesting that the developed materials had a double porous structure.     

环形截面提升管内颗粒的运动行为

采用PDPA(phase Doppler particle analyzer system)及磷光颗粒示踪技术对环形截面提升管中颗粒的运动行为进行了研究。与传统提升管相比，环形截面提升管中颗粒速度分布的均匀性有所改善，其最高速度与最低速度之差变小。环形截面提升管最大速度值出现在相对径向位置φ=0.3-0．4处。与传统提升管相似，环形截面提升管内颗粒的轴向返混较严重，停留时间分布曲线存在较明显的拖尾，其中颗粒的轴向Peclet数与传统提升管也处于同一数量级范围。提升管床结构的改变并未显著改变其中气固流动的微观相结构，稀相与密相颗粒团微观两相仍然存在，这种微观相结构是造成颗粒严重返混的决定性原因：稀相中的颗粒与密相颗粒团中的颗粒分别造成了颗粒停留时间分布曲线的前峰与拖尾峰。     

重组人EC-SOD包涵体的稀释复性及重折叠后蛋白的纯化

目的确定重组人ECSOD包涵体体外稀释复性和复性后蛋白纯化的适宜方法。方法通过对pH、温度、包涵体蛋白浓度、尿素和精氨酸浓度及氧化还原对比率的定性定量分析,研究重组人ECSOD包涵体体外稀释复性的基本条件。采用金属离子亲和柱(IMAC)和肝素亲和柱(Heparinsepharose)对复性蛋白进行纯化,比较纯化效率的差异。结果最佳复性条件为pH8.5,尿素浓度为1.5molL,精氨酸浓度大于0.3molL,GSH∶GSSG=4∶1;复性温度及包涵体蛋白终浓度越高,复性效率越低。IMAC和Heparinsepharose亲和柱均可用来纯化复性蛋白溶液,但Heparinsepharose纯化效率较高。结论确定了重组人ECSOD包涵体体外稀释复性的最佳条件及复性后蛋白纯化的方法。     

Humidity Sensor Characteristics of Woodceramics

The humidity sensor characteristics of Woodceramics were investigated. The Woodceramics used in this experiment were prepared at 650–900°C. The size of specimens selected was 1 × 1 × 10 mm . One was used as-cut and the other was polished. Above 700°C, the resistance of the specimen was below 50 and the decrease of resistance with increasing relative humidity was small. The specimen prepared at 650°C had a resistance of about 1 k. The resistance of as-cut specimens decreased with increase in relative humidity, but that of the polished specimen did not change significantly. The difference between as-cut and polished samples was explained by the differences in surface micro-structure.     

水性聚氨酯结构与微相分离的研究

合成了一系列水性聚氯酯，并用红外光谱、差示扫描量热仪对乳液胶膜进行表征，考察了软段组成、DMPA含量及。(-NCO)：n(-OH)比值对产物微相分离的影响。实验结果表明：聚醚型产物的微相分离程度高于聚酯型产物。提高DMPA用量，软段Tg移向低温区，说明体系的做相分离程度加大。随着n(-NCO)：n(-OH)比值的增大，软段Tg也移向低温区，软硬段的微相分离程度增大.     

Theoretical Models for Binder Burnout

The kinetics of binder burnout, from a ceramic green body, are considered for the case of an "unzipping" binder which decomposes to produce a volatile monomer. The process is considered to fail if the concentration of monomer in the green body exceeds that in equilibrium with vapor at 1 atm (≅10⁵ Pa), when an internal bubble would be expected to form. Steady-state diffusional calculations and computer simulations explore the size and temperature dependence of the process and are in agreement. The model suggests that it is not feasible to burn out a large flat piece greater than about 3 mm thick, without going to very long times of burnout. The kinetics are significantly improved if porosity develops in the piece during the early stages of decomposition, as opposed to the retreat of the binder into the piece on a uniform front.     

Characterization of nanoporous materials prepared from montmorillonite clay and its application to the decolorization of mare's milk oil

Nanoporous materials have been prepared by leaching the purified montmorillonite clay with sulfuric acid (H₂SO₄) solution with varying concentrations (0.5–2 M) at 80°C for 0.5–4 h. Acid leaching causes partial amorphisation of the clay with depletion of MgO, Al₂O₃, CaO and Fe₂O₃ components mostly from interlayer and octahedral sites. This increases the specific surface area by more than 3 times, i.e. from 49.1 to 157 m²/g. The pore-size distribution curves calculated from the adsorption isotherms of the leached montmorillonite show that most of the pores are in the mesoporous region with their diameter ranging 3–4 nm. This material turns out to be appropriate for bleaching of the mare's milk oil. The chemical and structural changes of the acid-leached montmorillonite are discussed in terms of the decolorization capacity.     

高强度超轻填料──氧化铝空心微珠

介绍氧化铝空心微珠的用途、性能及生产过程。     

重组人白细胞介素-10在大肠杆菌中的表达及生物学活性分析

目的在大肠杆菌中表达重组人白细胞介素-10(Interleukin-10,IL-10),并检测其生物学活性。方法将IL-10基因重组到质粒pET11c中,转化BL21(DE),提取质粒,经酶切鉴定和测序分析;在25℃用低浓度的IPTG诱导表达,对包涵体IL-10稀释复性;经ELISA检测其含量,MC/9细胞增殖法检测其生物学活性。结果工程菌IL-10/pET11c/BL21诱导表达的目的蛋白以可溶性和包涵体两种形式存在,Westernblot鉴定证实为IL-10蛋白,两种形式的IL-10均具有一定的生物学活性。结论已成功地在大肠杆菌中表达了IL-10,为进一步纯化和制备IL-10的基因工程药物打下了基础。