基于小波熵的电容器扰动识别和定位

对投电容器扰动识别和定位的方法进行了改进。针对其他此类方法的不足，比如在电压幅值低时投电容器扰动的识别、定位“可信度不高”等，文中通过提取小波变换的特定层的系数，对需要识别的电容器扰动的分解信号相对增强，而其他扰动的分解信号相对减弱，然后再提取熵特征值，结果表明它可以作为识别低电压时投电容器扰动的依据。在对电容器扰动进行定位时，参考了功率和能量定位法，并对其进行了改进。仿真分析证明，在电压幅值较低时，可以准确和可靠地对电容器扰动进行识别和定位。     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

超高分子量聚乙烯衬板在煤仓中的应用

介绍了井底煤仓溜煤斜面采用超高分子量聚乙烯衬板安装及应用情况 ,对井底煤仓棚煤原因及解决办法进行了探讨     

变风量空调系统

介绍了变风量空调系统（VAV系统）的特点、末端装置的型式以及最小送风量的确定方法，指出了VAV系统的研究重点和发展前景。     

热带城市垃圾典型组分的热解特性研究

对热带城市垃圾的几种典型组分进行了热解实验，得到了它们的失重曲线，通过对失重曲线进行分析，得到了这几种典型组分的热解规律，并通过建立热解动力学模型，求出了其中两种组分的活化能E和频率因子A。     

有扰对称信道平均信息量的计算

照相手机让诺基亚抢了风头，这真是亚洲人的失策。在日本和韩国，内置摄像头的手机早就不是什么值得炫耀的东西了。不过日本人的动作还是很快的，GD88和N8一副后来居上的架势，让人不敢小瞧。     

F150交换机告警关联规则的研究

为了提高电信网络运营效率，降低维护成本，电信运营企业在网络告警管理系统中需要引入数据挖掘技术。本文主要研究利用数据挖掘技术来进行故障的管理，即对告警进行关联性分析，详细分析了告警序列数据的关联规则挖掘算法，并在南昌本地网F150交换机的告警数据库中予以实现，同时对实际挖掘结果进行分析和整理，推导出一些实用的关联规则。     

Modeling of the bulk free radical polymerization up to high conversion—three stage polymerization model. II. Number-average molecular weight and apparent initiator efficiency

The equations for predicting the number-average molecular weight are derived on the basis of the three stage polymerization model (TSPM) in this paper. By applying the equations, a plotting approach is proposed to determine the apparent initiator efficiency defined as f[(α_td+1)/2] and the constant of chain transfer to monomer, where f is the initiator efficiency and α_td denotes the fraction of the termination rate constants by disproportionation. Using the approach to plot the experimental data in the literature, it is found that the chain transfer to monomer can be neglected for both methylmethacrylate (MMA) and styrene (St) polymerizations, but it can exert a significant effect on ethylmethacrylate (EMA) polymerization. In addition, the apparent initiator efficiency is found to be independent of reaction temperature and initiator concentration at each stage. The values of f[(α_td+1)/2] at gel effect stage are slightly reduced as compared with that at low conversion stage for MMA and EMA polymerizations. However, it decreases significantly at gel effect stage for St polymerization. Using the equations derived and the apparent initiator efficiencies obtained from TSPM plots, the number-average molecular weights at different conversions can be predicted. Comparisons show that the agreement between predictions and experimental data is satisfactory.     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002