探测激光超声信号的Fabry—Perot干涉仪及测试系统的研制

本文自行研制了一台Fabry—Perot干涉仪及其用于探测超声信号的测试系统。利用该系统对非光学表面的铝板和铜板实现了nm级窄脉冲激光超声信号的非接触式检测,其信噪比足以满足进一步信号处理要求。     

对聚合物驱单井效果评价的几点认识

通过对喇嘛甸油田聚合物驱单井效果分析，给出了采油井阶段效果评价方法，即单井见效时间和含水回升时间早晚的确定方法，单井见效时间取决于油层条件，注聚前含油饱和度及累计采出地下体积倍数，单井含水回升时间主要取决于聚驱阶段剩余储量采出程度，根据单井阶段评价结果，对试验区进行跟踪调整，在单井阶段效果评价的基础上，对单井最终效果采用吨聚增油量和聚驱阶段剩余储量采收率来进行客观，有效的评价，对聚驱产量预测具有一定指导意义。     

Charge density dependence of elastic modulus of strong polyelectrolyte hydrogels

The mechanical behavior of a series of strong polyelectrolyte hydrogels based on acrylamide and 2-acrylamido-2-methylpropane sulfonic acid sodium salt (AMPS) was investigated. The hydrogels were prepared at a fixed crosslinker ratio and monomer concentration, but at various charge densities, i.e. AMPS contents between 0 and 100 mol%. The elastic modulus of the hydrogels after their preparation first increases with increasing charge density but then decreases continuously. Investigation of the swollen state properties of the hydrogels shows existence of a large number of ionic groups inside the gel that are ineffective in gel swelling. The results indicate two opposite effects of charged groups on the elastic modulus of the hydrogels: formation of multiplets acting as additional crosslinks in the gel increases the elastic modulus of ionic hydrogels, whereas the effect of the electrostatic interaction of charged groups on elastic free energy decreases the modulus.     

高砂比压裂技术研究

应用由美国ＮＳＩ公司引进的“ｓｔｉｍｐｌａｎ”拟三维压裂设计软件，对影响裂缝内支撑剂铺置浓度的诸因素进行了灰色关联度分析，从中找出了主要的影响因素。并以高砂比压裂的技术指标为依据，研究了在目前压裂工艺水平下，进行高砂比压裂所必须遵循的原则。文中还对国内的高砂比压裂进行了实例分析，进一步论证了文中的观点。     

单线循环客运索道设计参数研讨(续三)

论证客运索道设计中的几个重要参数,建立抱索器钳口夹紧力计算公式,第一次给出钳口夹紧力与钢索金属断面积的比值,并进行了钢索弯曲应力计算公式的推导.     

基于锁相同步检测的数字化阻抗测试方法

介绍了一种数字化阻抗测试方法，它采用锁相同步采样、数字化矢量电压电流比法及校准技术测试元器件或线路阻抗。同时介绍了相应实验电路原理，并结合线路接口，进行了通信电缆的线路阻抗测试实验。     

Miniaturization and bandwidth enhancement of a cavity backed circular microstrip patch antenna

The resonant frequency of a circular patch antenna with and without circular cavity is measured. The patch miniaturization in the presence of the cavity is proved. Different methods of reducing resonant frequencies and broadening bandwidth without significantly reducing antenna gain are presented. Capacitively loaded patch and slits on the patch stimulate the patch at lower frequencies and multiple resonances, thus help miniaturization. Finally ferrite loading on the feed probe further increases the bandwidth without significantly reducing the antenna gain. The method is much more improved than that for a resistive loaded patch and a deformed patch. © 2007 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2007.     

Method of increasing the output signal-to-noise ratio in passive multi-element antenna arrays

A method of processing complex signals in passive multi-element antenna arrays based on an analysis of the natural values of the correlation matrix of the signal is considered. By means of the method it is possible to substantially increase the output signal-to-noise ratio. An iterational process by means of which optimal estimators of both the signal and the amplitude-phase distribution may be obtained, is proposed. Theoretical estimators of the efficiency of the method are given. It is proved that, in terms of the efficiency, the approach considered in the article comes close to the technique of matched filtration. Results of statistical modeling that confirm the statistical results are presented.     

矫直状态下钢管弹塑性变形区的研究

根据钢管矫直时的变形规律，通过对矫直中钢管的力学状态及矫直前后的状态参数分析，建立了一种适于现场应用的确定钢管弹、塑性变形区的新方法。