一种快速的海面特征SAR成像仿真技术

水下物体运动引起扰动，会在海面产生尾迹。这种尾迹特征同运动物体的参数和下潜的深度以及海况有关。研究这种尾迹特征及其合成孔径雷达(SAR)成像，就有可能利用SAR来检测这个水下运动物体。本文给出了一种水下运动物体的伴流尾迹的快速模拟方法及其合成孔径雷达(SAR)成像仿真方法，并对模拟仿真的结果进行了讨论。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

ON THE INVERTIBILITY OF PERIODIC MOVING-AVERAGE MODELS

Abstract. A sufficient condition for the invertibility of univariate periodic moving-average models has been given by Cipra and Ghysels and Hall. We show that this condition is not a necessary one, and provide a necessary and sufficient condition for the general m -variate, d -periodical moving-average MA( q ) case.     

孔型热轧时轧制力的实用计算公式

采用修正系数法,利用板材在带刻槽的冲头进行深冲与平面冲头下深冲时的接触压力的比值确定孔型影响系数,进而推导出孔型热轧时轧制力的实用计算公式.     

结构化P2P网络中基于流言传播的负载均衡

提出了结构化P2P网络中利用结点间周期性的拓扑维护通信来夹带、传播消息进行负载均衡的方法，具体针对Chord系统从消息传播的速度和规模两个方面分析了该方法的性能，并利用仿真进行了验证。讨论了结论在其它形式网络中的推广和实现中的消息管理问题。     

无粘结预应力卵形消化池的受力分析及设计

本文采用有限元计算分析软件ANSYS对近年来出现的卵形消化池进行计算分析,着重对卵形消化池在多种荷载下的内力与变形进行分析,并采用二次曲线模拟沿高度均匀变化的壁厚。提出适合卵形消化池结构预应力钢筋等效为均布荷载的计算与配筋方法,取得较好的结果。     

Decomposition of Time Series Dynamic Linear Models

This paper derives the admissible decompositions for a time series dynamic linear model, assuming only that the model is observable. The decompositions depend on factorizations of the characteristic polynomial of the state evolution matrix G into relatively prime factors. This generalizes the method of West (1997 ) which considers one decomposition in the particular case where G is diagonalizable. Conditions are derived for a decomposition to be independent. These results show that no autoregressive process of order d has an independent decomposition for any integer d . Two illustrations of this procedure are discussed in detail.     

集中载荷作用下的套管抗挤能力分析

根据油田套管损坏情况,建立了集中载荷作用下的套管抗挤能力计算模型,利用能量法和曲杆理论,分析研究了承受180°对称分布集中载荷、90°均匀分布集中载荷和120°均匀分布集中载荷下中厚壁套管抗挤能力,得出了理想圆管抗挤强度和套管屈曲临界挤毁压力的计算公式,通过分析比较理论解与有限元解,其最大相对误差不超过1%,得出了套管抵抗局部载荷的能力低于抵抗均布载荷的结论。     

就地补偿在动力厂水泵电机上的应用实例

本文就我公司动力厂给水车间155kW水泵电机，进行无功就地补偿的可行性分析及经济效益研究，对工厂用电如何节能降耗有一定参考价值观。