DC-DC电荷泵的研究与设计

以Dickson电荷泵的基本原理为出发点，研究了一种将正电压输入转为负电压输出的开关电容电路。由于开关电容的充放电特点，为确定电容时间常数，采用非交叠时钟控制信号避免了由于时钟交叠而造成的当电容充电还未完成即对下一级电容进行放电的现象。同时，参考功率MOS-FET的电容模型通过增大驱动电路的电流减小了开关管的上升延时，提高了开关动作的速度，使转换效率得到明显提高。此电路结构简单，性能优良，易于集成，可广泛应用于输出负电压的电源产品中。     

Prediction of foam growth and its nucleation in free and limited expansion

The influence volume approach (IVA) is often utilized for modeling the mass transfer process dictating bubble growth dynamics in physical foaming. However, the assumed concentration profile in the IVA method is only valid when the changes in dissolved gas concentration are small (less than 5%). In addition, the validity of the IVA method is difficult to justify in chemical foaming applications because of the difficulties involved in defining the dissolved gas concentration profile.In the present work, we define two distinct stages of bubble growth for physical foaming. These two stages are termed as free and limited expansion and are controlled by the bubble nucleation rate. Bubble nucleation is assumed to occur only in the free expansion stage. In this stage, the bubble pressure drops substantially from an initially high pressure in the supersaturated state while the dissolved gas concentration changes very little. The second stage of our two-stage mass transfer model is termed the limited expansion stage and accounts for bubble growth in the late stages of foam evolution, when the pressure changes become small. However, in the limited stage of bubble growth the dissolved gas concentration drops significantly, as the available dissolved gas is depleted. To summarize our two-stage mass transfer model of foam expansion, the pressure difference between the bubble phase and the liquid phase is the primary mechanism for driving mass transfer in the early (free) stages of foam growth and the concentration difference is the driver for bubble growth in the late (limited) stages of growth. The first stage can be regarded as the nucleation stage and it is relatively short; while the second stage can be regarded as the bubble growth stage and is much longer. Most of the bubble volume expansion takes place in the second stage.The concentration gradient at the bubble edge, which is often ignored in other models, is analyzed in detail in this paper. The details of our novel mass transfer model are also presented.     

氯气泵叶轮连续破碎原因

针对YLJ型液环式氯气泵叶轮在短期内频繁破碎的情况,对其破碎原因进行了分析,并提出相应的改进措施,使烧碱工艺系统保持了长、满、安、稳的运行状态。     

河南油田潜油电泵井远程无线监控系统研制

针对河南油田研制了一种潜油电泵井远程无线监控系统。详细介绍了该系统的软硬件组成及工作原理。系统研制的主要内容包括：数据及指令传输监控软件的开发。利用SQL Server实现相关数据的管理和实时数据的网络广播；该系统在河南油田建成后．缩短了开井周期。减轻了人工劳动强度，提高了采油效率。实现了电泵井的现代化管理。     

英台地区天然水驱油藏的开发特点及稳产技术

掌握边底水运动规律，控制并利用活跃的边底水能量，是成功开发天然水驱油藏的关键。英台地区的英台、四方坨子和一棵树等三个油田均为天然水驱油藏，天然能量充足。油藏投入开发后初期含水较高，含水上升极快，造成产油量大幅度递减。针对其开发特点，适时采用大泵、电潜泵提液强采，通过大量补孔层间接替以及加密调整和扩边等稳产技术措施，确保了油藏以3％-5％的采油速度长期稳产，水驱采收率高达50％以上。     

Optimum thermoeconomic and thermodynamic performance characteristics of an irreversible three-heat-source heat pump

The coefficient of performance and specific heating load of an irreversible three-heat-source heat pump are given by using a general cycle model affected by the finite-rate heat transfer, heat leak and internal irreversibility of the cyclic working fluid. The heat pumping load divided by the total cost per unit time is taken as a new objective function and used to investigate the performance of the heat pump. The thermoeconomic and thermodynamic performance characteristics of the heat pump are discussed in detail. Some important performance parameters such as the thermoeconomic objective function and coefficient of performance are optimized. The optimally operating regions of the heat pump and the bounds of several performance parameters are determined. Finally, it is pointed out that the Carnot heat pump may be taken as a special case of a three-heat-source heat pump and consequently its optimal performance can be directly derived from the results obtained here.     

液氨装置工艺计算及改造总结

介绍我公司液氯装置由活塞式氨气压缩机氨-CaCl2盐水系统改为带经济器的螺杆式氯气液化机组的工艺计算,新建装置特点以及改造后的装置在我公司运行情况和使用效果。经改造后的液氯装置每年可节约电费73万余元,同时提高了装置的安全可靠性。     

中央空调冷冻水泵变频调速运行特性研究(2):模拟计算与分析

利用前文的分析结果，对采用定压差控制的某空调系统进行了模拟计算，并将计算结果与相似定律所得结果进行了比较，表明直接按相似定律所确定的泵的扬程和能耗均偏低；同时对冷冻水管路系统中的雷诺数Re、沿程阻力系数和管路阻抗等随空调负荷的变化关系，以及空调负荷分布、压差设定值等对冷冻水泵变频运行参数及能耗的影响等方面进行了分析，提出了冷冻水泵变频的最有利及最不利工况，并根据模拟与分析结果对空调冷冻水泵变频调速系统的设计等提出了建议。     

双柱塞砂浆泵中工作机构的设计和仿真研究

本文介绍了双柱塞砂浆泵的工作原理，根据机构替代原理建立起双柱塞砂浆泵工作机构的运动分析模型，然后在MatLab环境下，详细介绍了工作凸轮曲线的设计程序，利用计算机设计程序可以方便地分析工作缸活塞以及工作凸轮机构的位移、速度、加速度，利用SIMULINK仿真工具箱进行运动学仿真，为工作机构设计提供相应的理论分析依据。     

海水泵房土石方开挖及大围堰施工回顾

着重说明海水泵房临海的大围堰工程是厂区土石方开挖和厂房施工的先决条件之一。外方设计方案偏离厂址实际情况 ,存在许多施工难题。中方根据厂区实际情况 ,提出新的施工方案 ,不仅保证了1 998年 6月 8日第一罐混凝土施工 ,还节约了几百万资金