底部两层框架-抗震墙砖房抗震能力的分析方法与设计控制

提出了底部两层框架 -抗震墙砖房框剪层和砖混层的极限受剪承载力、侧移刚度、极限剪力系数计算公式 ,并基于设置不同数量抗震墙的底部两层框架 -抗震墙砖房的实例计算和弹塑性时程分析 ,给出了结构砖混过渡层与相邻框剪层的极限剪力系数比和侧移刚度比的合理取值及薄弱楼层位置判别和破坏状态评定的方法和原则。     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.     

CMS/TiO2杂化材料电流变液的制备及其性能

利用特殊的溶胶凝胶方法原位制备了改性淀粉与无机钛氧化物杂化型电流变材料。实验表明,在强电场下其电流变效应比相同组份的淀粉、二氧化钛混合型电流变液有显著提高,直流电场4 kV/mm,剪切速率5 s-1时,静态剪切屈服强度可达4000 Pa以上。同时,抗沉降性明显改善,静置100 h几乎不沉淀。此外,温度效应也获得一定的优化,在10 ℃~90 ℃的工作温度范围内力学性能保持良好,70 ℃时剪切强度达到最大值。     

摩擦强度对薄膜表面形态的作用:原子力显微镜下的观察

展示了摩擦强度对聚酰亚胺薄膜表面形态的影响，原子力显微图像显示，机械摩擦会使聚酰亚胺薄膜表面上形成微沟槽，这些沟槽的表面具有丰富的表面精细构造。原子显微图像还揭示了机械摩擦可以改变被磨擦聚酰亚胺膜的表面形态。     

纵横波测井资料在储层评价中的应用

将弹性波基础理论，Gasman理论，Biot理论和实验研究结果相结合，探讨了沉积岩地层中速度和弹性模量，弹性模量和孔隙度，剪切模量和孔隙度，速度和孔隙度，孔隙度和Biot系数之间的关系，利用从各种声学测井资料中提取出的P波和S波时差（或速度）定量评价地层孔隙度和骨架物质，辅以泥质指示测井曲线，可以计算地层孔隙度，饱和度，岩性等参数，在M，Krief方法的基础上，采用优化算法寻求适合于任何岩性地层的孔隙度与Biot系数之间的关系式，提高了Biot系数的计算精度，该评价方法有坚实的实验基础和理论基础，评价结果与实验室岩心分析数据吻合。     

基于放大器非线性拟合的自适应预失真技术

本文提出了一种新的有效的大功率放大器非线性失真的数字自适应预失真设计方法。该方法基于有理双线函数的非线性及其逆变换易于求解的特性，设计大功率放大器的估计器以逼近大功率放大器的非线性特性，预失真器的非线性参数由估计器的逼近函数逐段取逆变换来调节，以达到预失真补偿的目的。计算机仿真结果表明：该方法用于正交频分复用（OFDM）系统中具有收敛速度快、系统性能稳定、补偿效果好等特点。     

光漂白法制备有机聚合物非线性定向耦合器

研究了用光漂白的方法制备PMMA/DR1聚合物非线性定向耦合器,提出了一种容易的制备方法来得到要求的耦合长度.测量了材料的光学非线性对定向耦合器两臂透过率的影响.实验结果表明由于光学非线性,耦合器的耦合长度随着入射光强度的改变而发生变化.     

Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。