Random errors caused by temperature in magnitude of principal strains evaluated ith 3-element strain gauge rosettes

The effects of the uncertainties associated ith the apparent strain and gauge factor data, given by the manufacturer, in the evaluation of principal strains are examined. Principal strains are obtained by a reduction of the strains measured ith electrical resistance strain gauge rectangular or delta rosettes. The theoretical analysis points out the relevance of the effects caused.     

Salt-water up-coning during extraction of fresh water from a tropical island

Rainwater can collect in a lens-shaped region within the rock of a tropical island, and may be separated from the underlying salt water by a sharp interface. This paper presents a nonlinear theory for determining the shape of this interface. The island is assumed to be saturated with rain, and provision is made for the outflow of rain-water through the sides of the island. The effect of a bore well on the shape of the interface is investigated, and the problem is solved using a spectral method. An integral-equation method is also presented for the case when the island has infinite width.     

黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Effect of flow on solutions of rod-coil block co-polymers

An elongational flow field is imposed on a solution of block copolymers consisting of semirigid macromolecules with rigid, rodlike sequences of units in combination with random coil (flexible) units. The problem is formulated according to the lattice treatment of Matheson and Flory. In this formulation, the system consists of rigid blocks whose lengths and locations are fixed by the structure within each macromolecule. These blocks are separated by random coiled units. An excess free energy other than the equilibrium Gibbs free energy of the quiescent solution has to be considered due to the flow field that tends to align the rods. This excess free energy is calculated from the potential energy of rods when a steady-state, homogeneous and irrotational flow field is applied to the solution. The effects of composition, polymer-solvent interaction, size of the co-polymer and flow rates are investigated. Depending on the size and number of rods, some of the chains studied exhibit a biphasic region at equilibrium that shifts to lower concentrations with increasing flow. Longer chains with shorter rods that are isotropic at equilibrium, exhibit a biphasic region at finite values of flow. The degree of orientation increases sharply when the system is biphasic. For larger flows, the orientation function is very close to unity which is perfect orientation.     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

浅谈低频小功率三极管的输入电阻的计算

就低频小功率三极管的输入电阻的计算进行了探讨。     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

A new adaptation of mapping method to study mixing of multiphase flows in mixers with complex geometries

The main objective of the present work is to modify the traditional mapping method for the simulation of distributive mixing of multiphase flows in geometries involving moving parts such as, internal mixers or twin-screw extruders without a limitation on their geometrical periodicity. The periodicity condition, limits the results of traditional mapping method to tracking mapping mesh between specific discrete time intervals or distances for that geometry is repeated, hence, result is only for fixed orientation of rotors. Imaginary domain method is introduced to track mapping mesh from one state to the next free of geometrical periodicity limitations. In this work the method is introduced and its applicability and accuracy is discussed in details. A two-dimensional (2D) simulation of mixing of two Newtonian fluids with different viscosities in an intermeshing internal mixer is used as a test case study. In this example the key issues of ability to predict mixing state in details for all orientations of rotors is presented. To reduce diffusion errors of mapping method in the boundaries of the rotors, mapping mesh refinement technique that relies upon one single reference mesh is also presented.     

风管摩擦阻力的直接计算方法

提出用高精度的反映密度、黏度和温度关系的经验公式和Colebrook公式计算风管摩擦阻力系数的方法。分析和算例表明，用该方法计算，计算结果比采用常用工程设计方法更为准确，为应用计算机进行风道设计提供了直接、简便的方法。