基于实际井眼轨迹的抽油杆柱API设计方法

目前的抽油杆柱设计方法大都基于设计井眼轨迹或经验公式，因此设计的抽油杆柱与井眼的匹配性并没有达到最优，结果可能影响了抽油杆柱的受力特性和寿命。概述了目前现有的抽油杆柱设计方法，提出了基于实际井眼轨迹的抽油杆柱API设计方法，即考虑到在三维空间中井下粘滞阻力及动载的影响，利用微单元分析方法计算出轴向载荷与轴向应力，然后在此基础上进行杆柱组合设计，并给出了设计流程。以江苏油田永21-3井为例，对几种设计方法的设计结果进行了对比分析，结果表明，江苏油田目前采用的抽油杆柱设计方法包含了人为经验因素，并不是最优的杆柱设计结果，有待进一步改进。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

A multigrid accelerated hybrid unstructured mesh method for 3D compressible turbulent flow

 A cell vertex finite volume method for the solution of steady compressible turbulent flow problems on unstructured hybrid meshes of tetrahedra, prisms, pyramids and hexahedra is described. These hybrid meshes are constructed by firstly discretising the computational domain using tetrahedral elements and then by merging certain tetrahedra. A one equation turbulence model is employed and the solution of the steady flow equations is obtained by explicit relaxation. The solution process is accelerated by the addition of a multigrid method, in which the coarse meshes are generated by agglomeration, and by parallelisation. The approach is shown to be effective for the simulation of a number of 3D flows of current practical interest. Sponsored by The Research Council of Norway, project number 125676/410 Dedicated to the memory of Prof. Mike Crisfield, a respected colleague     

Fatigue crack propagation of multiple coplanar cracks with the coupled extended finite element/fast marching method

A numerical technique for modeling fatigue crack propagation of multiple coplanar cracks is presented. The proposed method couples the extended finite element method (X-FEM) [Int. J. Numer. Meth. Engng. 48 (11) (2000) 1549] to the fast marching method (FMM) [Level Set Methods & Fast Marching Methods: Evolving Interfaces in Computational Geometry, Fluid Mechanics, Computer Vision, and Materials Science, Cambridge University Press, Cambridge, UK, 1999]. The entire crack geometry, including one or more cracks, is represented by a single signed distance (level set) function. Merging of distinct cracks is handled naturally by the FMM with no collision detection or mesh reconstruction required. The FMM in conjunction with the Paris crack growth law is used to advance the crack front. In the X-FEM, a discontinuous function and the two-dimensional asymptotic crack-tip displacement fields are added to the finite element approximation to account for the crack using the notion of partition of unity [Comput. Meth. Appl. Mech. Engng. 139 (1996) 289]. This enables the domain to be modeled by a single fixed finite element mesh with no explicit meshing of the crack surfaces. In an earlier study [Engng. Fract. Mech. 70 (1) (2003) 29], the methodology, algorithm, and implementation for three-dimensional crack propagation of single cracks was introduced. In this paper, simulations for multiple planar cracks are presented, with crack merging and fatigue growth carried out without any user-intervention or remeshing.     

化学-电解氧化法制备高铁酸钾的研究

本文用化学－电解氧化法制备高铁酸钾，克服了纯化学氧化法产品需要提纯和纯电解氧化法制备周期长的缺点，得到了高纯度的高铁酸钾晶体。     

选择测试阀在现场测试中的应用

选择测试阀是新一代全通径压控式测试器，在结构和性能上有了本质的创新，使现场操作更加简便、安全，对井筒条件要求低，更适用于高温、高压、深井、气井的地层测试，拓宽了地层测试和其它井下作业的兼容性。经7井次应用，其安全性、可靠性越来越得到认可。     

弯曲性分叉河道中污染物扩散性的初步研究

弯曲性分叉河道中水流特征复杂,对污染物扩散有很大影响。为了定量分析其水流特征对污染物扩散的影响,采用有限元方法求解弯曲性分叉河道中的污染物扩散数学模型,研究其中污染物扩散的状况。主要针对河道回流、绕流对污染物扩散的影响进行了详细数值模拟计算,并分别给出了可视化结果及平均的扩散距离。计算结果表明:边界层稍微减弱污染物的扩散,弯道分离使污染物扩散呈现多向扩散,而回流和绕流尾迹区使污染物很难扩散,从而有利于泄漏污染物的收集和集中治理。     

径向水平井弯曲转向机构影响因素仿真研究

针对径向水平井钻进中钻杆弯曲转向前进运动困难的问题,通过建立弯曲转向机构仿真有限元模型,对其主要影响因素:滑道轨迹曲率、间隙、工作压力、滚轮形状与位置和钻杆壁厚等用ANSYS软件进行仿真研究。研究表明:影响截面变形的主要因素是滑道曲率的改变和滑道摩擦因数,钻井失败时钻杆所受阻力的增大不是因为升高工作压力导致截面变形过大与滑道干涉所致,钻杆经校直段,钻头中轴线与校直中心线存在一定的角度,即钻杆的前进轨迹就会偏离理论值,或与地层干涉,或可能再次发生弯曲变形;另一主要原因是转向器滑道工作恶化。增加钻杆壁厚,降低工作压力和滑道摩擦因数,设计合理弯曲转向机构是解决问题的关键。     

有限元技术在数值试井中的应用

分析了试井技术的发展趋势，对有限元分析技术及其发展作了较为全面的介绍，重点阐述了利用有限元技术进行三维建模的方法和步骤，尤其是对复杂的非对称边界和非均质油藏的建模方法和技巧进行了深入探讨。利用数值试井技术，石油工程师可以方便准确地对复杂油藏和边界进行建模，试井的模拟过程和油藏任意位置的压力瞬间变化都可以通过图形和颜色的变化显示出来，解释的精度和速度都得到了大大地提高。