转子叶片在非均匀来流条件下的流体激振特性

该文通过研究得出非均匀来流对转子叶片流体激振的三个重要特征 :非均匀来流相对于转子叶片的非定常流中主频分量是产生叶片动应力的决定因素 ;非均匀来流的非均匀度 (相当于非定常流的波幅 )大小和叶片流体激振的动应力大小成正比 ;转子叶片流体的定常压力水平与叶片动应力的水平密切相关。图 4表 2     

接触传热表面粗糙度曲线的统计特征

测量了一般机械加工表面的轮廓曲线，基于小波变换提取了粗糙度曲线，分析了轮廓高度和接触峰高度的统计分布特征。研究结果表明，轮廓高度不服从严格的正态分布，但具有一定的正态性，而接触峰高度的统计特征与其评定标准有直接的关系。因此，对于接触热阻的计算模型来说，接触点数的计算应以合理选取接触峰的评定标准为前提。     

光纤光栅的长度对其峰值反射率的影响

利用耦合模理论,数值分析了当光纤光栅(FBG)折射率变化为均匀分布、直流切趾高斯分布时,光纤光栅长度对其峰值反射率的影响。研究结果对光纤光栅外腔半导体激光器的设计和性能优化具有重要的意义。     

On using peak amplitude and rise time for AE source characterization

Acoustic Emission (AE) signals, which are electrical version of acoustic emissions, are usually analysed using a set of signal parameters. The major objective of signal analysis is to study the characteristics of the sources of emissions. Peak amplitude(P _a ) and rise time(R _t ) are two such parameters used for source characterization. In this paper, we theoretically investigate the efficiency ofP _a andR _t to classify and characterize AE sources by modelling the input stress pulse and transducer. Analytical expressions obtained forP _a andR _t clearly indicate their use and efficiency for source characterization. It is believed that these results may be of use to investigators in areas like control systems and signal processing also     

Calculation of fatigue limits of case-hardened specimens with consideration of mean stresses and residual stresses

 The strength of case-hardened parts under cyclic loading can be determined in an experimental manner, but this can produce a large amount of costs due to the expenditure of material and testing time. Therefore, a calculation method is developed, that strongly reduces the number of experiments. The presented model is based on Weibull's weakest-link concept and allows to compute the survival probability of a case-hardened part which is loaded close to the fatigue limit. The essential quantities in this model are the distribution of Vicker's hardness of the material, the exponents of the Weibull distribution of the volume and the surface, the residual stress state, the surface roughness and the surface oxidation depth. By integrating the survival probabilities of the surface and the volume, the survival probability of the entire specimen or part can be calculated, which allows to compute the fatigue limit. The necessary parameters have to be determined from reference specimens. The model is successfully examined by comparing experimental and calculated results of smooth and notched case-hardened specimens under alternating torsion, rotating bending, repeated tension and tension-compression. Received 20 August 2001 / Accepted 11 November 2001     

影响塑料模压制件内应力的因素分析

主要讨论了造成塑料模压制件内应力的主要因素,包括制件造型设计不合理、模具设计不合理、成型工艺条件不正确等,并针对不同情况给出了相应的解决办法     

封隔器胶筒接触应力分布有限元计算

利用ANSYS软件对3种封隔器胶筒的接触应力进行了有限元计算，得到了接触应力沿胶筒轴向的分布情况。比较不同结构封隔器胶筒在相同条件下的接触应力分布，可知新型封隔器胶筒在高压下接触应力分布更为均匀合理，具有较好的应用前景。     

超薄氧化层中的中性陷阱对隧穿电流的影响和应变诱导漏电流

用数值分析的方法讨论了中性陷阱对超薄场效应晶体管(MOSFET )隧穿电流的影响.中性陷阱引起势垒的变化在二氧化硅的导带中形成一个方形的势阱.对于不同的势垒变化,计算了电子隧穿氧化层厚度为4nm的超薄金属氧化物半导体结构的电流.结果表明,中性陷阱对隧穿电流的影响不能被忽略,中性陷阱的存在使隧穿电流增加,并且通过这个简单的模型能够理解应变诱导漏电流的产生机制.     

推进波作用下的底泥起动

在介绍推进波作用下底泥起动特点的基础上，将上层水体作为粘性流体，底泥作为粘弹性体，推导了推进波作用下泥床面剪应力的表达式，并根据试验结果，给出了推进波作用下底泥起动时的床面剪应力与底泥流变参数的关系。     

Residual stress measurements in bevel gear after different production phases

This article discusses residual stress measurements by means of electrochemical removal of material layers with residual stresses and simultaneous measurement of strain on the opposite specimen side with strain gages. Exact measurements are impossible particularly because of the small bevel gear module. With the method presented, the average residual stresses in the tooth root plane and underlying layers are measured. Residual stress distribution after each consecutive production phase is plotted and analyzed. Residual stress measurements enable the engineer to adequately assess each individual production phase and by that improve the quality of the complete production process.