不同缝纫工艺下缝纫阻力的测试与分析

本文采用LM缝纫性测试仪对不同缝纫工艺下的针织物和机织物缝纫阻力进行了测试.测试了织物层数、织物正反面以及缝纫方向不同时,面料缝纫阻力的大小;测试了不同缝针、缝纫线时的缝纫阻力.实验结果表明:织物的缝纫阻力随织物的层数增加而成倍数以上的增大;机织物在45°角左右缝纫时,缝纫阻力最大;针织物在接近纵行和横列方向,缝纫阻力出现最大值;穿引缝纫线会增大缝纫阻力,但缝纫线对缝纫阻力的增大作用较缝针的作用微弱.同时,实验过程中还发现,针织物的缝纫阻力比机织物的不匀率高,缝针刺到纱线上的概率高,因此针织物不易于缝纫.本论文的研究,希望对服装加工给予帮助,以提高服装质量和服装加工效率.     

基于语文教学中渗透德育教育的探索

语文是基础教育的重要学科,也是思想道德建设的主要阵地。本文将从语文教学过程中如何进行德育教育,如何使学生在学习知识的同时学会做人处事谈一些体会,并就二者的关系以及具体的教学案例进行探讨,旨在从教学方法、情感熏陶、深挖教材这三方面着手进行语文教学中渗透德育教育的经验探索和推广。     

CO2激光焊接的同轴检测与熔透控制(Ⅱ)熔透状态同轴光信号的频域分析

利用CO2激光深熔焊等离子体光信号的同轴检测系统,提出了频谱重心的概念井以此来分析等离子体光信号的频谱特性,研究了平扳焊接时对应适度熔透状态时同轴光信号的顿域特征。结果表明,随激光功率增加或焊接速度减小,当焊接熔透状态从“适度熔透(小孔透)”变化到“仅熔池透”时对应2～6kHz段频谱重心位置向上(高额)跳变。     

TIG焊和PAW焊中活性剂对焊缝熔深的影响

针对常规TIG焊生产效率低、熔深小等问题，研究了TIG焊和PAW焊中应用活性剂对焊缝熔深的影响。结果表明，应用活性剂后，在同样的参数下，同传统TIG相比，活性剂能够大幅度提高不锈钢、铝合金和钛合金的焊缝熔深。对于PAW焊，熔深也有增加，但是增加的幅度不如TIG效果明显，但对焊缝成形有很好的改善。同时，活性剂对铝合金焊接背面能够起到保护作用。对于钛合金，活性剂除了增加焊缝的熔深外，还能够大幅度地消减焊缝产生的气孔。     

Prediction and verification of melting front in GTA weld pool of full-penetration

A thermal conduction model is applied to speed up the numerical analysis of the temperature distribution and the weld pool geometry of full penetration in gas tungsten arc （GTA） welding. With considering both top and bottom flee surface deformation of full-penetrated weld pool, three-dimensional weld pool with melting front and solidification front is predicted. Welding experiments are conducted to measure the melting front curves at the top surface and the longitudinal section of the weld. It shows that the predicted and measured results are in good agreement.     

单电源双面电弧焊接工艺实验研究

双面电弧焊接工艺（DSAW）是近几年新出现的一种焊接方法，它可以有效地增大焊缝溶深、提高焊接速度、节约能源消耗、降低焊接变形。本文对单电源DSAW工艺进行了实验研究，分析了双弧作用下焊缝熔深的变化规律，对双面电弧的收缩现象进行了观察，探讨了单电源DSAW工艺增大焊缝溶深的机理。     

Effects of blasting parameters on removability of residual grit

This article shows the quantitative evaluation of the residual grit on a blasted substrate, and the removability of the residual grit is examined. Carbon steel plates were blasted by white alumina grit with mean diameters of 338 to 1106 μm. The velocity and the number of grit particles were measured during blasting. The residual grit was removed from a substrate surface by the dissolution of the blasted substrate surface. A mixed acid solution was used as the dissolution solution. The residual grit weight was 7 to 17 g/m². The amount of the residual grit and the penetration depth of the embedded grit increased with increasing grit size. The penetration depth was 5 to 9% of the mean diameter of the grit. The residual grit weight and the penetration depth increased with the increase of the momentum of the grit particle. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, OH, 2006.     

The integrated intelligent system for welding seam error and penetration depth identification

A integrated intelligent system for seam tracking and penetration control is given. The system received information of welding seam error and penetration depth from only one sensor, then, it realized seam tracking and penetration control simultaneously. This paper introduces constitution of the system, methods of information recognition, design of the neuralfuzzy controller and results practically.     

Penetration treatment of plasma-sprayed ZrO2 coating by liquid Mn alloys

The penetration phenomena of liquid manganese (Mn) alloy into porous ZrO₂ (8 vvt % Y₂O₃) coating plasma sprayed on SS400 steel substrate was studied by heating in a vacuum atmosphere. The improvement in mechanical properties of the coating by heat treatment with liquid Mn alloys was examined. Liquid Mn alloys, such as Mn-Cu, Mn-Sn, and Mn-In, rapidly penetrated the coating and formed a chemical bond between the coating and the substrate. The densification of the ZrO₂ coating occurred when ZrO₂ particles were sintered with liquid Mn alloys that penetrated the porous coating. The dense coating was free of porosity, and its hardness increased after heat treatment with Mn alloys, compared with assprayed ZrO₂ coating. Moreover, the fracture toughness of the coating reached the same levels as those of sintered yttria-stabilized PSZ.     

水下粉细砂土体在超高频机械振动荷载作用下液化特性的试验研究

为了量化高频机械振动对土壤液化的具体效果,在试验室泥槽中对不同性质的水下粉细砂沉积物开展了诸如不同振动作用时间及不同工况下的液化试验,利用静力触探仪测量了振动作用前后其承载力变化情况,基于试验数据分析讨论了振动作用时间、振动作用距离、振动频率对于液化效果的影响.