Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

微机在应变测量中的应用

微机在应变测量中的应用，采用上位机和下位机组合方式．上位机为一台ＩＢＭ－ＰＣ／ＸＴ微机，用于对数据进行后处理．下位机以Ｚ８０－ＣＰＵ为控制器，由传感器、转换器、接口及外设等组成数据采集器，实施对应变、压力和位移等参数的采集、显示和打印（即数据的预处理）．上位机和下位机之间的数据传输，采用串行的方式，通过ＲＳ－２３２接口完成．本文主要以应变的采集处理为例，介绍系统功能、硬件配置及软件设计．     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

用SY87721实现城域网波分复用系统的多业务接入

为了使城域网的DWDM（密集波分复用）系统可以接入多种信号速率和格式，以满足用户的要求，首先介绍了一种波长转换板的设计方法，使用SY87721自适应提取28Mbit／s～2.7Gbit/s之间任意速率信号的时钟，其次介绍了SY87721提取时钟的工作原理、与单片机和CPLD（复杂可编程逻辑器件）的接口方式、对寄存器的配置和读出方式。最后介绍了使用参考时钟测量接入信号频率的方法，这会在系统维护时带来较大的方便。     

Polymerization strategies to overcome limiting monomer conversion in silicone-acrylic miniemulsion polymerization

The limiting conversion phenomenon observed in high solid content silicone-modified acrylic miniemulsion polymerizations was investigated. It was found that the limiting conversion was mainly due to the formation of inactive radicals upon propagation of butyl acrylate radicals with the vinyl end groups of the polydimethylsiloxane. Polymerization strategies that allowed overcoming this problem and achieving high monomer conversion were implemented.     

伴随内转换电子发射的俄歇电子能量及强度计算

简要介绍了伴随内转换电子发射产生的俄歇电子能量与强度的计算方法、计算程序及工作流程，并以^129Iβ^-衰变为例说明其具体应用。     

厦门市气源转换的技术分析

分析了气源转换时原有输配系统的管道、调压设备、计量设备、用气设备与天然气系统相适应的问题，提出了相应的措施。     

Efficient Legendre moment computation for grey level images

Legendre orthogonal moments have been widely used in the field of image analysis. Because their computation by a direct method is very time expensive, recent efforts have been devoted to the reduction of computational complexity. Nevertheless, the existing algorithms are mainly focused on binary images. We propose here a new fast method for computing the Legendre moments, which is not only suitable for binary images but also for grey level images. We first establish a recurrence formula of one-dimensional (1D) Legendre moments by using the recursive property of Legendre polynomials. As a result, the 1D Legendre moments of order p, L_p=L_p(0), can be expressed as a linear combination of L_p-1(1) and L_p-2(0). Based on this relationship, the 1D Legendre moments L_p(0) can thus be obtained from the arrays of L₁(a) and L₀(a), where a is an integer number less than p. To further decrease the computation complexity, an algorithm, in which no multiplication is required, is used to compute these quantities. The method is then extended to the calculation of the two-dimensional Legendre moments L_pq. We show that the proposed method is more efficient than the direct method.     

LD泵浦Nd：YVO4内腔倍频激光器获得120mW绿光连续输出

利用半导体激光器（ＬＤ）端面泵浦Ｎｄ：ＹＶＯ＿４和用ＫＴＰ内腔倍频的绿激光器获得了１２０ｍＷ连续、稳定的５３２ｎｍ绿激光输出。泵浦阈值Ｐ＿（ｔｈ）＝１６０ｍＷ，光－光转换效率η＿ｓ＝８．１％。换用激光腔输出耦合镜，在不加ＫＴＰ晶体倍频时，可连续输出１．０６μｍ的红外激光，输出功率为４５０ｍＷ，光－光转换效率为３１％。