国产50%离子膜法烧碱蒸发装置及运行情况

介绍了升降膜法双效逆流蒸发生产50%离子膜法烧碱的工艺流程、主要设备、装置特点及运行情况.     

Heat and Mass Transfer Analogy Studies of Binary Liquid Mixture in Comparison with Eteanol-n-Heptane Evaporating to Air

An expenmental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 mls. An illustrative example of the use of the theory for industrial ventilation is presented.     

蒸发冷凝法中气体压强和蒸发温度对粒子大小的影响

在Ｎ＿２气氛中，用蒸发冷凝法，制备了Ｓｎ细微粒和Ｆｅ及Ｆｅ－４７（ｗｔ）％Ｎｉ合金超细微粒。分别用ＳＥＭ和ＴＥＭ，直接观测粒子大小及其分布。结果表明，平均粒径不是随Ｎ＿２气压强增加单调上升，而是在某一压强Ｐ＿（ｍａｘ）下，出现最大值。随蒸发温度提高，Ｐ＿（ｍａｘ）值迅速增大。粒子大小及其分布与粒子生长机制密切相关。对粒子凝聚生长条件进行了简要讨论。     

瓶组气化站的建筑、结构设计要点

瓶组气化站的建筑，结构设计关系到安全，满足使用要求和投资的大小，本文根据多年的实践和最新的有关设计规范的要求，阐述瓶组气化站建筑，结构设计的要点。     

降膜蒸发过程的数值模拟和传热传质分析

利用CFD软件对逆流降膜蒸发过程进行了实验模拟研究,研究了速度边界层、热边界层和浓度边界层的变化对降膜蒸发传热传质特性的影响规律;通过建立一维逆流降膜蒸发的数学方程编程求解出了对流传热传质的Nu数和Sh数,利用Fluent软件模拟出的实验结果采用回归分析得出了气液流量比Raw、流道的长宽比αL、空气进口无量纲温度θai以及空气进口Re数与Nu数、Sh数之间的无量纲关系式,可为降膜蒸发换热器的设计提供参考。     

Electron beam deposition and characterization of thin film Ti-Ni for shape memory applications

Thin film of Ti-Ni alloy has a potential to perform the microactuation functions required in the microelectromechanical system (MEMS).It is essential, however, to have good uniformity in both chemical composition and thickness to realize its full potential as an active component of MEMS devices.Electron beam evaporation technique was employed in this study to fabricate the thin films of Ti-Ni alloy on different substrates.The targets used for the evaporation were first prepared by electron beam melting.The uniformity of composition and microstructure of the thin films were characterized by electron probe microanalysis (EPMA), Auger electron spectroscopy (AES), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and transmission electron microscopy (TEM).The mechanical property of the thin films was evaluated by the nano-indentation test.The martensitic transformation temperature was measured by differential scanning calorimetry (DSC).It is confirmed that the chemical composition of deposited thin films is identical to that of the target materials.Furthermore, results from depth profiling of the chemical composition variation reveal that the electron beam evaporation process yields better compositional homogeneity than other conventional methods such as sputtering and thermal evaporation.Microstructural observation by TEM shows that nanometer size precipitates are preferentially distributed along the grain boundaries of a few micron size grains.The hardness and elastic modulus of thin films decreases with an increase in Ti contents.     

Conductivity enhancement in transparetn ZnO films via Al-dopping produced by CW-CO2 laser-induced evaporation

Highly conductive transparent aluminium-doped ZnO (ZnO:A1) films were successfully deposited by CW-CO₂ laser-induced evaporation. Optimisation of evaporation parameters was based on laser power, substrate temperature, O₂ partial pressure in the vacuum chamber and amount of Al in the ZnO source pellet. ZnO:A1 films with an electrical resistivity as low as 6.6 × 10⁻²Ω·cm and an optical transmission of 80% at 500nm were obtained at laser power of 15 W, substrate temperature of about 200°C, O₂ partial pressure of 6—7 × 10⁻⁴ Torr and 5wt.% Al. Conductivity of ZnO films can be increased one order via Al-doping in ZnO films. The films obtained by laser-induced evaporation have compared quite favorably with the high quality films obtained by sputtering.     

气相色谱法测定有机化合物的蒸发热

本文用气相色谱测定了多种烷烃、芳烃、醇类和酯类的蒸发热。结果表明,测定数据与文献数据基本一致,误差一般在±5%以内。是一种简单、快捷的测定方法。     

降低蒸发系统中结盐的措施

分析了液碱蒸发装置结盐对蒸发传热系数、生产能力和蒸汽消耗的影响。通过减少盐进入量，降低蒸发装置结盐速率和优化操作来解决蒸发系统的结盐问题，达到了降低汽耗、提高效能的目的。     

Preparation of Protein-Stabilized β-Carotene Nanodispersions by Emulsification–Evaporation Method

This work was initiated to prepare protein-stabilized β-carotene nanodispersions using emulsification–evaporation. A pre-mix of the aqueous phase composed of a protein and hexane containing β-carotene was subjected to high-pressure homogenization using a microfluidizer. Hexane in the resulting emulsion was evaporated under reduced pressures, causing crystallization and precipitation of β-carotene inside the droplets and formation of β-carotene nanoparticles. Sodium caseinate (SC) was the most effective emulsifier among selected proteins in preparing the nanodispersion, with a monomodal β-carotene particle-size distribution and a 17-nm mean particle size. The results were confirmed by transmission-electron microscopy analysis. SC-stabilized nanodispersion also had considerably high ζ-potential (−27 mV at pH 7), suggesting that the nanodispersion was stable against particle aggregation. Increasing the SC concentration decreased the mean particle size and improved the polydispersity of the nanodispersions. Nanodispersions prepared with higher β-carotene concentrations and higher organic-phase ratios resulted in larger β-carotene particles. Although increased microfluidization pressure did not decrease particle size, it did improve the polydispersity of the nanodispersions. Repeating the microfluidization process at 140 MPa caused the nanodispersions to become polydisperse, indicating the loss of emulsifying capacity of SC due to protein denaturation.