金属清净剂的性能研究

为了改进金属清净剂的抗氧性和极压抗磨性能，用一种含硫磷的羧酸衍生物部分中和清净剂中过碱性组分，得到两种改进的金属清净剂，并用四球机和热重分析仪评价其极压抗磨和抗氧化性能。结果表明功能化处理提高了金属清净剂抗氧化和极压性能，但未对分散和抗磨性能产生显著影响。     

快速评定砂浆配方对钢筋腐蚀的影响

用电化学方法测定砂浆试件中钢筋的极化电阻，并测定了砂浆的孔隙率，结果发现:砂浆的孔隙率、孔径分布与钢筋极化电阻大小有良好的对应关系。电化学方法能可靠、快速测定砂浆配合比、添加剂对钢筋腐蚀速度的影响。     

泥沙起动条件及机理的非线性研究

 分析了单颗粒、均匀沙及非均匀沙的起动现象及其机理，认为泥沙的起动属于突变论研究的范畴。从泥沙起动所遵循起动条件的力学规律出发，导出泥沙起动条件方程。在此基础上，利用尖点突变性质对各种泥沙起动现象及机理进行了描述和说明。     

离子注入对Cr12MoV钢表面组织结构和力学性能的影响

研究了Ｃｒ１２ＭｏＶ钢离子注入层的显微组织特征及其对表面性能的影响。结果表明，离子注入使Ｃｒ１２ＭｏＶ钢的表面硬度和耐磨性能得到显著改善，且存在着一个最佳的注入剂量，约为３×１０＾１＾７Ｎ＾＋／ｃｍ＾２左右。离了注入在Ｃｒ１２ＭｏＶ钢表面层中形成了大量细小弥散的第二相粒子，并使α－Ｆｅ晶格发生严重畸变，从而引起材料表面强化。     

ZnO陶瓷材料的负阻特性

介绍了ＺｎＯ陶瓷的负阻特性，主要研究了ＭｎＯ２掺杂和Ｎｉ２Ｏ３掺杂对ＺｎＯ陶瓷负阻特性的影响。     

方块电阻测试中的有限元理论

介绍了用有限元方法计算半导体方块电阻四探针测试中二维点电流势场的模型并且证明了其正确性。由于有限元方法对边界没有限制，该方法为方块电阻测试中精确确定边界修正系数，更重要的是为微样品测试结构确定提供直接明了的理论依据。     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

聚苯胺锂基润滑脂载流润滑下的摩擦学性能

制备了导电聚苯胺锂基润滑脂（简称PANI脂）和铜基银镀层材料（简称银层材料）。采用摩擦磨损试验机考察在无载流、载流及边界润滑条件下，铜基体材料（简称铜基材料）和银层材料的摩擦磨损性能。采用X射线衍射（XRD）、扫描电子显微镜（SEM）和电子能谱（EDS）对银层材料晶相及其表面磨斑形貌进行表征。结果表明，载流条件下，PANI脂润滑试验时的银层材料不仅具有良好的减摩抗磨性能，而且导电能力更强，其优异的减摩和抗磨性能归功于摩擦表面的保护膜和电流热效应引起的表面软化双重作用。     

Effect of reliability of grounding of the shaft of a turboset on the operation of devices for control and protection of exciting circuits

Disturbance of the grounding of the shaft of a turboset or its absence for technical reasons can result in failure, misoperation, limitation of the operating zone, errors or limitation of the sensitivity of devices for control and protection of exciting circuits from single-point leakage, and electroerosion of elements of the turboset structure. Measures for increasing the reliability of the grounding of the shaft are discussed. __________ Translated from élektricheskie Stantsii, No. 3, March 2006, pp. 61–66.