Method of increasing the output signal-to-noise ratio in passive multi-element antenna arrays

A method of processing complex signals in passive multi-element antenna arrays based on an analysis of the natural values of the correlation matrix of the signal is considered. By means of the method it is possible to substantially increase the output signal-to-noise ratio. An iterational process by means of which optimal estimators of both the signal and the amplitude-phase distribution may be obtained, is proposed. Theoretical estimators of the efficiency of the method are given. It is proved that, in terms of the efficiency, the approach considered in the article comes close to the technique of matched filtration. Results of statistical modeling that confirm the statistical results are presented.     

Development and implementation of a NURBS curve motion interpolator

This paper deals with the issues of development and implementation of a real-time NURBS interpolator for a six-axis robot. Using an open-architecture controller system as a testbed, a real-time NURBS curve interpolator was developed, implemented and tested. Sample runs were conducted with the resulting trajectories measured in real-time during robot motion. The resulting trajectories are analyzed, discussed and compared with those from a commonly used point-to-point approximation technique. The real-time NURBS curve interpolator's feasibility, advantages and related issues are also discussed.     

布尔函数的对偶性和线性点

本文主要讨论了部分自对偶和部分反自对偶函数、部分线性函数以及具有线性点的函数的性质。     

The Danish Twin Apartment Study – Part II: Mathematical modeling of the relative strength of sources of indoor air pollution

Abstract This study deals with the modeling of air pollution in apartments from laboratory measurements of source strengths, using formaldehyde and Total Volatile Organic Compounds (TVOCs) as model pollutants. The sources in two test apartments were grouped into two: building-related sources and occupant-related sources. The measured source strengths and ventilation rates were used for the prediction of concentrations expected in the apartments. These predictions were compared to measurements in the apartment over 12 months. The conclusions were that the model predictions based on emission rates measured in the laboratory can be used to predict the long-term concentration of the two model pollutants in the apartments. Considering the measured differences in ventilation between the apartments, an occupant emission rate of between 0.2 and 0.3 mg/h/kg body weight could be estimated. Based on previous suggested limits of acceptable exposures of humans to VOCs, an acceptable average emission rate of VOCs from building materials in general was estimated to be about 30 (μ/m²/h. The modeling showed that during the first 200 days, building materials dominated the emissions. After this, sources relating to the occupants dominated. On average about half of the VOC pollution originated from the building materials.     

Cubic Bézier approximation of a digitized curve

In this paper we present an efficient technique for piecewise cubic Bézier approximation of digitized curve. An adaptive breakpoint detection method divides a digital curve into a number of segments and each segment is approximated by a cubic Bézier curve so that the approximation error is minimized. Initial approximated Bézier control points for each of the segments are obtained by interpolation technique i.e. by the reverse recursion of De Castaljau's algorithm. Two methods, two-dimensional logarithmic search algorithm (TDLSA) and an evolutionary search algorithm (ESA), are introduced to find the best-fit Bézier control points from the approximate interpolated control points. ESA based refinement is proved to be better experimentally. Experimental results show that Bézier approximation of a digitized curve is much more accurate and uses less number of points compared to other approximation techniques.     

矫直辊与板材的接触点位置对矫直过程影响的研究

介绍了辊式矫直过程中，板材与矫直辊的接触点位置对矫直过程的影响，以及接触点对矫直过程影响的一系列研究，最后对接触点在矫直过程中的分析方法及作用进行了预测。     

遵义后坝奥陶系红花园组油苗岩石轻烃特征分析

遵义后坝奥陶系红花园组生物碎屑灰岩中发现油苗和沥青,经过气/源岩、沥青/源岩对比,震旦、寒武及奥陶系产层轻烃C₆₊₇结构组成基本一致,奥陶系含油苗灰岩轻烃星图与震旦系泥岩、寒武系沥青砂岩星图较为相似,显示红花园组油苗主要来源于震旦系和下古生界过成熟或高成熟海相烃源岩,油气经历了较长距离的运移,得以在奥陶系中保存下来。这对评价该地区油气前景有重要意义,预示着可能存在一套特殊的含油气组合,存在以O₁h古风化壳储集层为目的层的勘探领域。在兴文—叙永一线以西地区现今下古生界储盖组合保存良好,在适当的构造圈闭中可形成油气藏。志留系和二叠系产层轻烃C₆₊₇与震旦系、寒武系及奥陶系等产层轻烃C₆₊₇明显有别,星图对比性差,表征它们之间成烃母质或沉积环境均有不同。      

北非库弗腊盆地油气成藏条件及地质风险初探

库弗腊盆地是在稳定结晶基底上形成的大型古生代克拉通内坳陷盆地。油气地质评价认为，该盆地发育始寒武系一自垩系的浅海相与河流相交互沉积，依据钻井、露头、孢粉组合可将其沉积序列划分为8套地层单元。推测盆地存在3套烃源岩：始寒武系泥岩、奥陶系泥岩、志留系Tanezzuft组泥岩，其中Tanezzuft组泥岩是盆地最有可能的烃源岩。库弗腊盆地可能存在奥陶系一志留系和始寒武系两套成藏组合，盆地模拟结果表明盆地的两个沉积中心（uri槽和Kalanshiyu槽）的烃源岩已达到生油窗范围，是否存在有效烃源岩是决定该盆地油气潜力的主要因素和油气勘探的最大地质风险所在。图4参18