SO3和C3A对水泥膨胀性能的影响

本文研究了ＳＯ３和Ｃ３Ａ对水泥浆体膨胀的影响。对于某一较早的龄期，当ＳＯ３掺量超过某一数值时，水泥浆体的膨胀与ＳＯ３掺量关系不大，而提高水泥的Ｃ３Ａ含量则能显著地增加其膨胀。本文还探讨了ＳＯ３和Ｃ３Ａ影响水泥浆体膨胀的机理。     

马来酸及其酐和衣康酸与PP熔体接枝反应机理的研究

以马来酸酐作对照，用热分析、流变、化学分析等方法，研究了马来酸和衣康酸在非隔氧条件下与ＰＰ熔体催化接枝反应的特点和规律，阐述了单体结构－单元反应相对速率－－接枝产物结构之间的关系，提出了３种接枝物的结构模型。     

1477 nm LD泵浦掺铒光纤放大器的研究

报道了采用１４７７ｎｍ激光二极管（ＬＤ）泵浦的掺铒光纤放大器的实验结果。研究了放大器的增益和时域特性。对１５２０ｎｍ的信号光，获得了２３ｄＢ的增益，泵浦效率为２．２８ｄＢ／ｍＷ。低频脉冲信号经过放大器后未发生波形畸变。     

被动锁模复合环形腔掺饵光纤激光器的自启动分析

本文对被动锁模复合环形腔掺饵光纤激光器的自启动工作特性进行了分析，指出谐振腔内残余反射面的存在是阻碍激光器实现自启动锁模的主要原因。利用半导体激光器有源区的折射率随注入电流的变化而改变的特性，在谐振腔中获得了一个可移动腔镜，克服了腔内残余反射面的影响，实现了锁模的自启动。     

Standard reference materials for cements

The eight portland cements and two calcium aluminate cements in the Standard Reference Material (SRM) 1880 series are among the most popular SRMs in the catalog of the National Institute of Standards and Technology (NIST) Standard Reference Materials Program. Numerous laboratories rely on them for elemental analysis and qualification for ASTM C 114-00 Standard Test Methods for Chemical Analysis of Hydraulic Cement. NIST has collected new candidate materials from around the world and partnered with Construction Technology Laboratories (CTL) in their preparation and certification. This paper describes the procedures taken at NIST and CTL to prepare and test materials for certification including the homogeneity testing, the X-ray fluorescence methods and the statistical data analysis performed for value assignment.     

Influence of synergists: The influence of hydroperoxide decomposers on phenolic inhibitors consumption in oxidized polypropylene

The influence of sulphur‐ and phosphorum‐containing substances (hydroperoxide decomposers) on the kinetics of the consumption of two phenolic antioxidants in polypropylene (PP) was studied. The induction periods of PP autoxidation at 130°C were measured in the presence of inhibiting compositions that consisted of phenolic inhibitors and decomposers of hydroperoxide. Obtained results indicated that the influence of the hydroperoxide decomposer became significant when the concentration of the phenolic antioxidant became close to critical value. It also was shown that the efficiency of the hydroperoxide decomposer significantly depended on the mechanism of the transformation of the phenolic inhibitor; and first of all on the nature of its transformation products. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2239–2243, 2002     

Characterization of hollow fiber membranes in a permeator using binary gas mixtures

We have studied the CO₂/CH₄ mixed gas permeation through hollow fiber membranes in a permeator. An approach to characterize the true separation performance of hollow fiber membranes for binary gas mixtures was provided based on experiments and simulations. Experiments were carried out to measure the retentate and permeate flow rates and compositions at each outlet. The influences of pressure drop within the hollow fibers, non-ideal gas behavior in the mixture and concentration polarization were taken into consideration in the mathematics model. The calculation results indicate that the net influence of the non-ideal gas behavior, competitive sorption and plasticization yields the calculated CO₂ permeance in a mixed gas permeator close to that obtained in pure gas tests. Whereas the CH₄ permeance is higher in the mixed gas tests than that in the pure gas tests, as the plasticization caused by CO₂ dominates the permeation process. As a result, the CO₂/CH₄ mixed gas selectivity is smaller than those obtained in pure gas tests at equivalent pressures.The calculated membrane performance shows little changes with stage cut if the effect of concentration polarization is accounted for in the calculation. The integration method developed in this study could provide more accurate characterizations of mixed gas permeance of hollow membranes than other estimation methods, as our model considers the roles of non-ideal gas behavior and concentration polarization properly.     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

HPVC／PP共混改性研究：Ⅲ低分子量反应性化合物作相容剂

采用低分子量反应性化合物作相容剂，即化学交联体系来改善ＨＰＶＣ／ＰＰ共混物的相容性。考察了在不同共混比下，不同化学交联体系对共混物力学性能的影响，并观察了共混物的微观形态。结果表明，采用低分子量反应性化合物作相容剂，共混物的拉伸强度提高，但冲击强度无改善。分散相尺寸减小，相间粘接得到改善。并比较了３种增容方法的效果，发现ＣＰＥ是ＨＰＶＣ／ＰＰ共混物的最佳相容剂。     

Study on high-strength composite portland cement with a larger amount of industrial wastes

It is one of important measures for the sustainable development of cement industry to utilize industrial wastes. High-strength composite portland cement with a large amount of granulated blast furnace slag (GBFS), fly ash and limestone was prepared by separate grinding method, optimizing gypsum and using activators. The total amounts of blending materials are between 45% and 65% and the strength grades of cements reach 525 or even 625 according to Chinese national standard for composite portland cement. Besides setting time and strength, the hydration heat, drying shrinkage and sulfate resistance were also determined.