变质Mn8Crl耐磨钢弥散组织的形成机制

研究了变质Ｍｎ８Ｃｒｌ耐磨钢弥散处理过程中显微组织、物相硬度及成分的变化。结果表明，通过热处理获得理想弥散组织的条件：首先是奥氏体锰钢中含有适量的强碳化物形成元素，其次是使奥氏体尽可能充分地发生珠光体转变，三是适当控制高温阶段等温温度和时间。     

高碳Cr—Mo—W钢M／B复相组织疲劳行为研究

用紧凑拉伸试样测定了65Cr5Mo3W2VSiTi(LM2)钢不同贝氏体量和不同回火温度的M/B复相组织的疲劳裂纹扩展速率,根据试验数据估算了各工艺的疲劳门槛值。结果表明,LM2钢M/B复相组织的疲劳裂纹扩展属非连续扩展机制,疲劳裂纹微观扩展速率的计算值和宏观扩展速率的实测值相近     

High-velocity oxyfuel thermal spray coatings for biomedical applications

Plasma spraying is used to produce most commercially available bioceramic coatings for dental implants; however, these coatings still contain some inadequacies. Two types of coatings produced by the high- velocity oxyfuel (HVOF) combustion spray process using commercially available hydroxyapatite (HA) and fluorapatite (FA) powders sprayed onto titanium were characterized to determine whether this relatively new coating process can be applied to bioceramic coatings. Diffuse reflectance Fourier transform infrared (FTIR) spectroscopy, x- ray diffraction (XRD), and scanning electron microscopy (SEM) were used to characterize the composition, microstructure, and morphology of the coatings. The XRD and FTIR techniques revealed an apatitic structure for both HA and FA coatings. However, XRD patterns indicated some loss in crystallinity of the coatings due to the spraying process. Results from FTIR showed a loss in the intensity of the OH^∼ and F^∼ groups due to HVOF spraying; the phosphate groups, however, were still present. Analysis by SEM showed a coating morphology similar to that obtained with plasma spraying, with complete coverage of the titanium substrate. Interfacial SEM studies revealed an excellent coating-to-substrate apposition. These results indicate that with further optimization the HVOF thermal spray process may offer another method for producing bioceramic coatings.     

小口径钢管全位置脉冲TIG多层焊的组织分析

采用全位置脉冲TIG焊技术对小口径钢管环缝进行焊接，焊接采用TIG焊打底＋TIG填丝的多层焊工艺，分析了打底焊及每层填丝焊接完成后的打底层焊缝组织。结果表明，采用多层焊工艺可以很好地避免焊缝及热影响区的扩大，并且后焊层对前焊层的再加热作用，可细化晶粒，改善组织。     

热变形后低铬耐磨铸铁的组织与耐磨性的关系

研究了低铬耐磨铸铁经40％热变形及不同方式冷却后的组织与耐磨性的关系。结果表明：该铸铁经热变形后的组织与耐磨性有良好的对应关系，其耐磨性随硬度的增加而增大，同时也与组织中碳化物的形状、大小及分布有关。     

合金化对非晶形成能力影响的电子理论计算

根据分子动力学理论建立了非晶Ni64Pd16Al20的结构模型，利用Recursion方法计算了Ni64X17Al20系非晶及相应晶态的电子结构。结果表明，Ni64X16Al20合金的非晶形成能力与过渡元素局域电子态密度的双峰位置、电子得失形成的离子键及非晶与晶态合金的总结构能差有关。局域电子态密度的结果表明，A1与过渡元素间存在电子耦合一共价相互作用，合金元素使Ni64X16Al2合金非晶形成能力从强到弱的顺序是：Ir，Pt，Rh，Pd，Au，Ag，Cu；Ni64X16Al20合金中离子键的存在使其非晶形成能力增强。非晶与晶态合金的总结构能差越小的过渡元素使其形成非晶的驱动力越强，对非晶形成越有利，由此得出的规律与上述共价键的作用规律一致。     

冰箱门面板冲压工艺分析及模具设计

分析冰箱门面板的冲压工艺,介绍模具设计中应注意的问题及滚压式结构的特点     

Oxidation behavior of TiAl coated with a fine-grain Co-30Cr-4Al film

The oxidation behavior of TiAl coupons coated with a fine-grain Co-30Cr-4Al (mass %) film of about 30-m thickness has been studied at 1100–1400 K in a flow of purified oxygen at atmospheric pressure for up to 500 ks. Three oxidation stages were recognized: initial transient, parabolic, and accelerated stages. However, at 1100 K a parabolic stage continues for more than 800 ks. The activation energy for parabolic oxidation agrees with reported values for the oxidation of alumina-former alloys, although the mass gains during the parabolic stages are relatively small at 1200 and 1300 K. Micropores developed mainly at the scale/coating and coating/substrate interfaces as oxidation proceeded. This is attributable to recrystallization of the coating during oxidation and a Kirkendall effect due to preferential diffusion of Co into the substrate. The accelerated oxidation can be explained in terms of the formation of rutile mounds on the scale.     

基于塑性变形有限元模拟的模具结构优化

本文对马鞋6061铝合金塑性成形过程进行了有限元数值模拟分析,模拟发现了坯料充不满等缺陷.通过改进模具结构,数值模拟表明：采用阻料设计可防止缺陷的产生,并提高材料的利用率,降低成形压力.     

基体组织对蠕墨铸铁热疲劳性能的影响

主要研究了基体组织对蠕墨铸铁抗热裂性能的影响，为高速列车制动盘的合理选材提供依据。试验结果表明：铁素体基体蠕墨铸铁的耐热疲劳性能优于珠光体基体蠕墨铸铁。