测井新技术在四川油气勘探开发中的应用

综述随着四川盆地油气勘探深入所面临的油气领域复杂和困难的技术问题，介绍应用测井新技术为四川油气开发解决了大量的技术难题，特别是在复杂缝，洞型储层的评价，井旁地质构造形态精细分析和地质，测井，地震多学科结合储层横向预测等3个方面所取得的良好应用效果。     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

气液固三相相平衡热力学模型与计算方法

原油中含有大量的高分子有机固相物质，因此，要准确地描述油气体系相平衡，必须对气液固三相相平衡进行研究，在对高分子有机烃类沥青沉降机理有了一定的认识的基础上，提出了大的交互作用系数，可以描述沥青与原油中轻质不相容性的程度。根据对油气烃类混合物体系的一般性认识与提出的沥青组分特征化方法，导出了与之相应的有其自身特殊性的气液沥青三相相平衡物料平衡方程组，用考虑沥青沉降三相闪蒸数值算法，对沥青沉降进行有效的理化模拟计算，此外，结合实例分析，给出了沥青质参考逸度的计算，饱和压力和沉降量的拟合方法。     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

市区微蜂窝传播路径损耗模式的比较检验

讨论了几种微蜂窝路径损耗模式,并用我国某城市测量的微蜂窝传播数据对COST231WI,修正COST231WI和Xia模式进行了检验,结果表明修正COST231模式的误差最小,Xia模式次之,COST231WI模式最差。从而得到修正COST231模式比较符合我国实际的微蜂窝传播预测模式。     

"十五"农村水电发展分析与"十一五"发展预测

本文分析了"十五"期间农村水电发展情况,对"十一五"农村水电发展政策环境及增长情况进行了预测。     

种分Δαk与种分首槽αk的关系

针对烧结法和拜尔法种分槽的 Δαk 变化进行了概述 ,阐述了种分 Δαk 与种分首槽 αk 的关系。     

Exceptions that prove the rule--Using a theory of motivated social cognition to account for ideological incongruities and political anomalies: Reply to Greenberg and Jonas (2003).

A meta-analysis by J. T. Jost, J. Glaser, A. W. Kruglanski, and F. J. Sulloway (2003) concluded that political conservatism is partially motivated by the management of uncertainty and threat. In this reply to J. Greenberg and E. Jonas (2003), conceptual issues are clarified, numerous political anomalies are explained, and alleged counterexamples are incorporated with a dynamic model that takes into account differences between "young" and "old" movements. Studies directly pitting the rigidity-of-the-right hypothesis against the ideological extremity hypothesis demonstrate strong support for the former. Medium to large effect sizes describe relations between political conservatism and dogmatism and intolerance of ambiguity; lack of openness to experience; uncertainty avoidance; personal needs for order, structure, and closure; fear of death; and system threat. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Characterization of strength properties of thin polycrystalline silicon films for MEMS applications

The aim of this work is to characterize the strength properties of polycrystalline silicon (polysilicon) with the use of tensile and bending test specimens. The strength of thin polysilicon films with different geometry, size and stress concentrations has been measured and correlated with the effective size of the specimen and its stress distribution. The test results are evaluated using a probabilistic strength approach based on the weakest link theory with the use of STAU software. The use of statistic methods of strength prediction of polysilicon test structures with a complex geometry and loading based on test values for standard material tests specimen has been evaluated.