Existence, uniqueness and stability of the equilibrium points of a SHARON bioreactor model

This paper addresses the dynamics of a SHARON reactor, a promising technology for ammonium removal from concentrated wastewater streams. The contraction mapping theorem is used to determine which operating conditions of a SHARON reactor with pH-control result in a unique equilibrium state. However, this approach only identifies the case of very large dilution rates, in practice corresponding with complete biomass wash-out, i.e. with complete loss of biological activity. Practical operation of a SHARON reactor aims at reaching ammonium conversion to nitrite. To identify such interesting operating points, the equilibrium points are subsequently calculated directly in terms of input variables for a simplified SHARON reactor model. The stability of the obtained equilibrium points is assessed and the corresponding phase portraits are analyzed. The influence of slightly varying parameter and input values is investigated as well.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

高放废液化学成分分析

概述了高放废液中25种阳离子、5种阴离子以及总蒸残物、总氧化物、密度和游离酸的分析方法。对核燃料后处理高放废液进行取样分析,其主要化学成分采用两种以上不同原理的方法作对比测定,结果相互符合情况良好,为高放废液处理处置研究设计,提供了完整、准确的基础数据。     

砌筑砂浆达不到设计要求的事故原因分析

从砂浆的配合比、和易性、原材料等对砌筑砂浆达不到设计要求的事故原因进行了分析。     

Approximating the problem, not the solution: An alternative view of point set matching

This work discusses the issue of approximation in point set matching. In general, one may have two classes of approximations when tackling a matching problem: (1) an algorithmic approximation which consists in using suboptimal procedures to infer the assignment, and (2), a representational approximation which involves a simplified and suboptimal model for the original data. Matching techniques have typically relied on the first approach by retaining the complete model and using suboptimal techniques to solve it. In this paper, we show how a technique based on using exact inference in simple Graphical Models, an instance of the second class, can significantly outperform instances of techniques from the first class. We experimentally compare this method with well-known Spectral and Relaxation methods, which are exemplars of the first class. We have performed experiments with synthetic and real-world data sets which reveal significant performance improvement in a wide operating range.     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

On the cost of searching signature trees

A precise analysis of the retrieval of signature trees is presented. A signature tree is a data structure constructed over a signature file to speed up searching all those signatures, which match a given query signature. The methods used include a detailed study of probabilistic analysis in conjunction with suitable contour integration of complex variabled functions.     

胃动力信息采集与分析系统设计

本文设计了一套提取胃电和胃阻抗信号的胃动力信息采集与分析系统，该系统由采集系统和分析系统两部分构成。前者以单片机（ADuC834）为核心部件，实现了胃电和生物阻抗信号的同步采集和数据传输。后者对提取的阻抗信号和胃电信号运用小波多分辨分析处理，利用小波变换将胃阻抗信号从呼吸和血流信号中分离。系统可以应用于分析功能性消化不良患者胃动力的电过程和机械过程。     

Geotechnical properties of the soft soil in Guangzhou College City

The paper describes some geotechnical properties of the soft soils in Guangzhou College City, China, which are difficult to both sample and test. Laboratory and in situ tests were carried out to assess the physical and mechanical indices of the soils. The data were statistically analyzed and linear regression undertaken such that equations could be developed by which the geotechnical properties of the soft soils can be predicted. The statistical validity of the degree of correlation confirmed that using these equations, the mechanical indices can be estimated from physical indices determined by routine testing.      

Signature analysis and defect detection in layered manufacturing of ceramic sensors and actuators

This paper presents the concept of a process signature for the use of online signature analysis and defect detection in the layered manufacturing (LM) of ceramic sensors and actuators. To achieve the high quality of parts built by the fused deposition of ceramics (FDC), an online process-monitoring system is implemented to detect the processing defects. Using a process signature extracted from the image of a layer captured by the monitoring system, an ideal image is created that is then compared to the original image to detect and identify the defects. Some results of signature analysis and defect detection for single-material and multi-material parts are also presented.Received: 22 July 1999, Accepted: 21 October 2001, Published online: 29 October 2003 Correspondence to: Mohsen A. JafariThis work was supported by the Office of Naval Research under grant # N-0014-96-1-1175. Ref. US Patent # S-5738817, April 14, 1998.