成形工艺对快速凝固Al—Cu—Mg合金组织和性能的影响

采用自制离心雾化装置制取了快速凝固LY12硬铝合金粉末,研究了以该粉末制成的真空热压件和挤压丝材的组织和性能。结果表明,所得粉末为泪滴状,其显微组织为树枝状晶和胞状晶。真空热压件密度高时所对应的强度高。450℃、10min、150MPa为较合理的工艺,此时粉末颗粒间结合密实,晶粒尺寸没有明显改变。在500℃热挤压时,挤压丝的组织已发生了再结晶,晶粒尺寸仍较细小。挤压丝材的抗拉强度达460MPa,其断口为韧窝状,韧窝尺寸小于3μm,且分布均匀。     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.     

Targets and methods for the detection of processed animal proteins in animal feedstuffs

Bovine spongiform encephalopathy (BSE), or ‘mad cow disease’, is one of several transmissable spongiform encephalopathies (TSEs) known to affect certain mammals and is spread through the ingestion of infected animal tissue. It is believed that the inadvertent contamination of meat and bone meal (MBM) with infected animal tissue and the subsequent use of this material as a feed supplement contributed to the spread of the disease in cattle. As a result, the use of processed animal proteins (PAPs) in animal feeds is regulated in many parts of the world. Although feed testing is the only definitive means to certify compliance, regulatory compliance often relies solely on paper certification. Recently, rapid methods have become available that can be used by regulators to determine compliance during routine inspections. We describe a rapid, immunochromatographic strip test that can detect 0.1% MBM in animal feed. The test takes 15 min to perform and large numbers of samples can be screened for PAPs simultaneously.     

低温液体冷却循环器的研究与开发

根据低温生物、生化实验研究和产品小试时应用低温条件的特点，提出机械制冷的冷却循环器，讨论了工作原理和制冷量计算，对其制冷系统和温度控制进行介绍。     

骨组织工程PLGA/TCP复合材料的性能研究

骨组织工程的支架要求有与人骨在功能梯度上相一致的材料结构、几何结构和生理功能。PLGA／TCP复合材料具有适用于骨组织工程支架的综合性能。以快速成形技术低温沉积工艺的成形效果来评价材料的成形性能，以体外降解试验来评价材料的降解性能，以国家标准的方法来评价材料的细胞毒性，对PLGA和TCP不同配比下的性能进行了研究，发现TCP含量的增加有利于降低材料的细胞毒性，加快了材料的降解，但同时降低了材料的成形性能。从骨组织工程的临床应用来看，低的细胞毒性是需要首先得到保证的，成形性能则通过其他方式来改善。     

内燃机车临时补水设备的设计与应用

针对内燃机车“途中缺水”故障 ,设计并安装临时补水设备 ,解决了电化区段临时补水的问题 ,满足了内燃机车“不停车、不停机”即可补水的要求。     

轧后穿水冷却工艺对棒材组织性能的影响

针对轧机产量提高后冷床冷却能力不足的问题 ,研制开发了棒材轧后穿水冷却技术。通过对小规格 2 0MnSiV热轧带肋钢筋进行轧后穿水冷却 ,钢材上冷床温度降低了 90～ 110℃ ,提高了产品质量 ,改善了各项力学性能 ,抗拉强度平均提高了 3 5～ 40MPa ,钢材性能合格率由 97.5 %提高到了 99.6% ,解决了冷床冷却能力不足、制约生产的瓶颈问题。     

冷却水污垢及其对冷却器换热的影响

分析了冷却器的结垢机理 ,提出了冷却器污垢层、污垢热阻随运行时间的规律 ,以及污垢热阻与换热系数、换热面积的关系式 ,并通过算例阐述了污垢热阻对冷却器的影响程度 ,进而定性地分析了污垢热阻对空分装置的影响。     

机械过冷的制冷系统在汽车空调中的应用

由于很多汽车空调采用斜盘式压缩机，有利于采用机械过冷的制冷系统，来增加汽车空调的制冷量、提高制冷效率。本文的主要目的是通过对系统工质的流量分配、空调制冷量和性能系数(COP)与中间压力之间的变化关系的研究，来研究机械过冷在汽车空调中应用的可行性。     

可再生能源在空调制冷中的应用

针对目前压缩式制冷技术带来的能源短缺和环境污染问题，介绍了几种可再生能源在空调制冷中的应用技术，如地道风供冷、地源热泵系统、太阳能空调制冷，分析了可再生能源用于空调制冷的特点及发展现状，并对其应用前景做了展望。