井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

WPAN/WLAN应用环境下基于PER的链路自适应算法

本文重点研究基于包错误率测量的链路自适应算法，分析了包错误率与信道参数的关系，提出了一种有别于固定门限值方案的优化门限值方案。仿真结果表明，优化门限值方案的网络吞吐量要大于固定门限值方案和基于信干比估计的链路自适应算法，最大增幅可达12Mbit/s。在系统引入重传机制后，网络吞吐量将有所损失，但最大不超过1Mbit/s，相比较服务质量的提高是值得的。需指出的是，虽然分析和仿真均以HIPERLAN／2为例，但不失一般性，它们同样适合于WPAN/WLAN等类似系统。     

高分辨率地震资料处理中的优化速度分析方法

速度分析是地震资料处理过程中的重要一环。速度分析的质量直接影响动静校正,继而影响叠加成像以及偏移归位。针对如何优化速度分析,提出了基于道集资料噪音衰减、道集内相位时差校正、道集优化处理以及速度拾取应用约束等过程的优化速度分析方法。该方法在实际资料处理中取得了很好的效果。     

Use of X-ray computed microtomography to understand why gels reduce relative permeability to water more than that to oil

X-ray computed microtomography (XMT) was used to investigate why gels reduce relative permeability to water more than that to oil in strongly water-wet Berea sandstone. XMT allows saturation differences to be monitored for individual pores during various stages of oil, water, and gelant flooding. The method also characterizes distributions of pore size, aspect ratio, and coordination number for the porous media. We studied a Cr(III) acetate–HPAM gel that reduced permeability to water (at S_or) by a factor 80–90 times more than that to oil (at S_wr). In Berea, the gel caused disproportionate permeability reduction by trapping substantial volumes of oil that remained immobile during water flooding (i.e., 43.5% S_or before gel placement versus 78.7% S_or after gel placement). With this high trapped oil saturation, water was forced to flow through narrow films, through the smallest pores, and through the gel itself. In contrast, during oil flooding, oil pathways remained relatively free from constriction by the gel.     

基于系统矩阵有序实Schur分解的模型降阶

对复杂高阶系统进行模型简化，为研究与设计系统提供了方便的条件。对系统模型的降阶是控制系统设计与仿真工作者的一个重要研究课题，对高阶复杂系统的分析、设计、仿真等具有重要的理论意义和工程实用价值。针对目前比较成熟的基于系统矩阵的有序实Schur分解方法，提出了采用时矩输出拟合来改善降阶系统输出响应逼近程度的改进方法，从而使简化模型具有输出误差更小、计算简便等优点，通过给出的实例仿真证实了这一点。     

Role of Perceived Importance in Intergroup Contact.

Furthering G. W. Allport's (1954) contentions for optimal contact, the authors introduce a new construct: the perceived importance of contact. They propose that perceived importance is the best proximal predictor of contact's reduction of prejudice. If individuals have opportunities for contact at work or in the neighborhood, their chances to have intergroup acquaintances and friends increase. Intergroup contact among acquaintances and friends can be perceived as more or less important, which in turn determines intergroup evaluations. A 1st study shows that the new measure of perceived importance is indeed distinct from established quantity and quality indicators. The results are cross-validated in a 2nd study that also sheds light on the meaning of importance. In 3rd and 4th studies, structural equation analyses and a meta-analysis support the hypotheses. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

MRC分集接收的MQAM在Nakagami信道上的性能分析

Nakagami信道是一种适应性较强的信道模型，MQAM(M-ary quadrature amplitude modulation)是一种频谱利用率较高的调制方式。在存在多径影响的无线通信环境中，最大比合并(maximum ratio combining)方式的分集接收是克服衰落的有效方法。本文利用适用范围更广的Nakagami信道模型，在多径衰落的情况下对最大比合并分集接收的MQAM系统误符号率性能作了分析。仿真结果对分析实际信道下具体系统的性能具有一定的参考价值。     

复杂目标的近场散射特性分析

详细分析了目标散射随距离而变化的特征，根据散射特点的不同将目标的散射特性分为远场散射、准近场散射、近场散射等三种情况，并对三种情况下的描述的手段进行了讨论，提出在近场条件下，用反射功率比的概念直接对散射目标的特性进行描述。     

一种制氢预转化催化剂还原的新方法

对上海高桥分公司2×10~4m~3/h(标准状态)制氢装置原设计的预转化催化剂还原流程进行了改进。先跳开预转化反应器,利用转化炉制取氢气,再用自产的高纯氢气代替重整氢,对预转化催化剂进行单独升温还原,避免了催化剂在还原初期因发生甲烷化反应而超温失活的问题,使催化剂具有更好的活性和稳定性。     

Signal Integrity: Fault Modeling and Testing in High-Speed SoCs

As we approach 100 nm technology the interconnect issues are becoming one of the main concerns in the testing of gigahertz system-on-chips. Voltage distortion (noise) and delay violations (skew) contribute to the signal integrity loss and ultimately functional error, performance degradation and reliability problems. In this paper, we first define a model for integrity faults on the high-speed interconnects. Then, we present a BIST-based test methodology that includes two special cells to detect and measure noise and skew occurring on the interconnects of the gigahertz system-on-chips. Using an inexpensive test architecture the integrity information accumulated by these special cells can be scanned out for final test and reliability analysis.