粘土矿物用于乙烯聚合催化剂的研究 Ⅰ.以凹凸棒石粘土为载体的乙烯聚合催化剂

研究了以凹凸棒石粘土为载体,负载TiCl4制备的乙烯聚合催化剂的结构、性能及制备规律。结果表明,催化剂中Ti的负载量随焙烧温度的提高而逐渐降低,聚合活性随焙烧温度的提高呈上升趋势,但过高的焙烧温度也会导致粘土晶体结构的彻底破坏而不利于活化粘土活性的提高;通过采用烷基铝等有机金属化合物处理粘土同样可以极大地改善粘土性质,提高催化活性。不同助催化剂对以凹凸棒石粘土为载体的催化剂的聚合性能有较大影响。     

对称配筋小偏心受压构件的截面设计

对小偏心受压构件在对称配筋情况下的截面配筋计算，提出用最佳一次逼近多项式简化基本公式，直接按二次方程求解ξ的近似方法，具有精度高，相对误差小，计算方便等优点，可供工程设计人员参考。     

太钢不锈冷轧工程防腐蚀施工技术

防腐蚀施工工艺掌握的好坏，直接影响到工程投入生产后的使用寿命，为保证工程质量，以太钢不锈冷轧改造工程冷线防腐为例，对其常发生的质量通病进行认真分析，总结出一套行之有效的施工技术。     

Fracture toughness of thermoset composites reinforced by perfectly bonded impenetrable short fibers

The fracture toughness of brittle thermoset resins could be improved significantly by perfectly bonded tough, short fibers through both crack trapping and bridging effects. In this paper, the crack trapping effect was studied through the analysis of the change of strain energy associated with the crack propagation across a regular array of fibers, and the bridging effect was discussed based on the Andersson–Bergkvist model. The fracture resistance increases with the fiber volume fraction, and is independent of the elastic properties of the matrix, the crack length, and the cross-sectional diameter of the fibers.     

Deflection Calculation of FRP Reinforced Concrete Beams Based on Modifications to the Existing Branson Equation

Fundamental concepts of tension stiffening are used to explain why Branson’s equation for the effective moment of inertia Ie does not predict deflection well for fiber reinforced polymer (FRP) reinforced concrete beams. The tension stiffening component in Branson’s equation is shown to depend on the ratio of gross-to-cracked moment of inertia (Ig/Icr), and gives too much tension stiffening for beams with an Ig/Icr ratio greater than 3. FRP beams typically have an Ig/Icr ratio greater than 5, leading to a much stiffer response and underprediction of computed deflections as observed by others in the past. One common approach to computing deflection of FRP reinforced concrete beams has been to use a modified form of the Branson equation. This paper presents a rational development of appropriate modification factors needed to reduce the tension stiffening component in Branson’s original expression to realistic levels. Computed deflections using this approach give reasonable results with the right modification factor, and compare well with a more general unified approach that incorporates a realistic tension stiffening model. Comparison is made with the existing and past correction factors recommended by ACI 440 for predicting deflection of FRP beams. The method presently used by ACI 440 gives reasonable estimates of deflection for glass and carbon FRP reinforced beams. However, this method underestimates deflection of aramid FRP reinforced beams and is restricted to rectangular sections. A proposal is made for adoption of a simple modification factor that works well for all types of FRP bar and beam cross-sectional shape.     

Proposed Design of a CFRP Flange-to-Flange Connection for Precast Prestressed Double Tee Systems

The current methods of connecting the flanges of precast double tee members, and their respective short comings in specific situations, are described. A new carbon fiber-reinforced polymer (CFRP) flange-to-flange connection is proposed to eliminate the problems associated with repair requirements for the current connections. Design expressions for the currently used mechanical anchorage and the proposed CFRP connection are presented. A comparative calculation for the two systems is given.     

Case Study-Based Challenges of Quality Concrete Finishing for Architecturally Complex Structures

This paper focuses on the procedure utilized in the construction of tilt-up irregular concrete panels that are constructed on-site using concrete slabs and wooden formwork. The case study required high-quality concrete finishing. The erection and installation procedure called for a maximum panel-to-panel joint tolerance of 1.27?cm (0.5?in.), often 90° joints between panels. To meet precision requirements, the casting slabs were leveled and flattened with laser screed technology and smoothed with chemical solutions. To ensure that the final result met expectations, a mock-up model was built using different types of materials and to simulate site constraints. The architectural design is a composition of precast concrete panels like “Lego” pieces assembled similarly to a jigsaw puzzle. The unique construction process required a state-of-the-art analysis to produce the set quality. Quality conditions as set by the owner included creating a smooth concrete surface on all panels while avoiding damages and reducing equipment and material costs. The proposed methodology is described through its implementation on the case study, which is also described in this paper.     

实用钢筋混凝土梁板结构优化设计

本文比较全面地考虑了钢筋混凝土梁板结构实际设计时的全部必要约束,给出了一套(单跨矩形和T形梁、单向板、按弹性理论计算的双向板和矩形等截面连续梁)简单实用的近优化设计的解析公式,为编制其优化设计的实用程序和图表提供了根据.     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry