严寒地区大型倒虹吸工程管道应力及水力安全控制

新疆北疆供水工程跨越吉拉沟大洼槽的三个泉倒虹吸,跨度11 km,内径2.8 m,工作水头160m,是国内外同类工程中综合难度较高的大型倒虹吸工程,在结构强度、材料工艺、安装敷设、工程质量方面都有极高的要求,特别是高水头管道运行、充水、放空、水锤防护等各种工况下的水力安全控制问题,高温差与严寒条件下管道的应力应变问题尤为突出。对该工程设计、科研、施工及运行管理方面的经验进行介绍,对其在新技术、新材料、新工艺等方面取得的理论研究和技术创新成果进行总结,研究认为:工程总体布置合理,工程运行后监测资料及工程安全评价表明各项性状指标良好,通过模型试验研究确定的闸门开度、关闭速率、充水排气、放空排水等水力安全控制关键技术科学合理,为严寒地区大型倒虹吸工程的技术发展提供借鉴。     

等强条件下橡胶微粒混凝土抗压特性及弹性模量研究

掺加橡胶微粒可以明显改善混凝土的力学特性。采用橡胶微粒等体积取代细骨料的方法,通过不断调整配合比,反复试验配制出橡胶微粒体积掺量分别为0%、10%和15%的等强度(30 MPa)橡胶微粒混凝土,探讨橡胶微粒混凝土的抗压强度变化规律,以及在等强条件下不同橡胶微粒掺量对混凝土弹性模量的影响。结果表明:掺入橡胶后,混凝土的前期强度(3 d和7 d)发展较基准混凝土变缓,7 d以及14 d后强度出现较大幅度的增长,28 d后各个配比混凝土立方体抗压强度增幅不大;掺入一定量的橡胶后,混凝土的抗裂性能得到了一定程度的改善,橡胶微粒体积掺量越大,试件受压破坏后的完整性越好;掺入橡胶后,混凝土的弹性模量呈现出近乎线性的大幅下降趋势。     

再生骨料的基本物理力学性能试验研究

再生骨料的物理力学性质是影响其运用范围、再生混凝土性能的本质因素。通过对公路废弃混凝土所制成的再生骨料和天然骨料同时进行物理力学性能试验研究,获得了骨料的表观密度、吸水率、压碎值、磨耗损失和针片状颗粒含量值。通过对再生骨料和天然骨料的试验结果进行对比分析发现,再生骨料除了针片状颗粒含量值会略优于天然骨料,其他四种物理力学性质均比天然骨料差,但两者的差异性不大。     

阿尔塔什水利枢纽工程深厚砂砾石覆盖层混凝土防渗墙施工技术研究

阿尔塔什水利枢纽工程是我国在建面板堆石坝工程之一,其深厚的砂砾石覆盖层和庞大的坝体,在施工和运行过程中均会对防渗墙的应力应变产生较大的影响,处理不好直接会影响到大坝整体防渗效果和工程安全。如何在保证施工质量的前提下,优化施工方案,改善防渗墙应力状况,是施工技术研究重点。通过对防渗墙的受力特性、深厚覆盖层的工程特性分析和研究,从防渗墙成墙槽段划分、墙段连接技术、强漏失地层成槽技术和固壁泥浆配比等关键技术上进行优化和改进,有效的消减了防渗墙在坝体填筑和蓄水过程中的应力应变集中,保证防渗墙的成墙质量和运行效果。     

大开口高承载网格加筋壳的设计与工艺

本文采用有限元法计算了承受高轴压和外压作用下的大开口复合材料纵横密加筋壳的稳定性，得出不同铺层角度、不同受力工况下的大开口圆柱壳的临界载荷，并采用1：1试验件进行试验验证，将计算值与实验值进行了比较；对大开口复合材料纵横密加筋壳的缠绕工艺进行了研究，解决了大开口网格加筋壳开口补强的一次成型技术和密筋及开口部分的多丝嘴、无增量、非线性机械化缠绕成型工艺技术。     

Hot compaction of woven nylon 6,6 multifilaments

We describe a study of the hot compaction of woven nylon 6,6 multifilaments produced by a patented procedure, developed at the University of Leeds, for creating novel single‐polymer composites. In this process, an assembly of oriented elements, often in the form of a woven cloth, is held under pressure and taken to a critical temperature so that a small fraction of the surface of each oriented element is melted, which on cooling recrystallizes to form the matrix of the single‐polymer composite. This process is therefore a way of producing novel high‐volume‐fraction polymer/polymer composites in which the two phases are chemically the same material. Nylon is an obvious candidate material for this process because oriented nylon multifilaments are available on a commercial scale. The aim of this study was first to establish the conditions of temperature and pressure for the successful hot compaction of oriented nylon 6,6 fibers and second to assess the mechanical properties of the manufactured hot‐compacted nylon sheets. A crucial aspect of this work, not previously examined in hot‐compaction studies of other oriented polymers, was the sensitivity of the properties to absorbed water, with a significant change in the properties measured immediately after hot‐compaction processing and 2 weeks later when 2% water had been absorbed by the compacted nylon sheets. As expected, the water uptake had a greater effect on those properties that depended on local chain interactions (e.g., the modulus and yield strength) and less effect on those properties that depended on the large‐scale properties of the molecular network (e.g., strength). The only negative aspect of the properties of the hot‐compacted nylon sheets was the elevated‐temperature performance of the wet sample, with the modulus falling to a very low value at a temperature of 80°C. However, apart from the elevated‐temperature performance, the majority of the measured properties of the hot‐compacted nylon sheets were comparable to those of hot‐compacted polypropylene and poly(ethylene terephthalate). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 991–997, 2006     

Influences of metallic polymeric materials on the properties of fresh polyester and acrylic polymer concrete

To investigate the influences of three metallic polymeric materials in polyester and acrylic fresh polymer concretes (PCs), PC‐incorporated different levels of these materials have been investigated for their properties of fresh PC. The mix design was made and optimized for workability, strength, and economy, depending on the resin viscosity, the intended use, and the additional quantities of these polymeric materials. The properties investigated include workability, working time, and curing time of fresh PC. It is concluded that these polymeric materials offer the possibility of improving properties of polyester and acrylic fresh polymer concretes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

含碳硫硅酸钙腐蚀产物的微观结构与生成机理

通过X射线衍射分析、扫描电镜、X射线光电子能谱分析、Fourier变换红外光谱分析及激光Raman光谱分析等现代测试技术,分析英国某桥墩基部腐蚀产物的微观结构,证实所取样品中含有大量的碳硫硅酸钙晶体,已发生了明显的碳硫硅酸钙型硫酸盐侵蚀.探讨了碳硫硅酸钙的腐蚀机理.     

一种聚羧酸型高效减水剂的试验研究

采用溶液共聚合成了一种聚羧酸型高效减水剂,对合成中影响减水剂性能的各种因素进行了分析;运用正交实验法,得出了合成该减水剂最佳配方和工艺条件;并研究了该减水剂对水泥净浆性能和混凝土性能的影响。结果表明,该产品掺量少(1.2%)、分散性能好(减水率25.4%)、混凝土性能高(抗压强度比178%)、不含甲醛等有害物,是一种良好的混凝土减水剂。     

试析钻孔灌注桩基础施工技术在桥梁工程中的应用

通过以某桥梁工程为例,探析了钻孔灌注桩基础施工技术在桥梁工程中的具体应用,并为类似桥梁工程的基础施工人员提供了一定的参考和依据。