In situ formation of multi scale reinforcing phases to improve performance of Al2O3-SiC C castables

In order to improve the physical properties and slag corrosion resistance of refractory materials for hot metal pretreatment, different contents of composite metal powders (CMP) were introduced into Al2O3-SiC-C refractory castables. The effect of CMP on the microstructure, physical properties and slag corrosion resistance of Al2O3-SiC-C refractory castables were studied. The results show that the multi scale reinforcing phases including flake crystals, rod shaped fibers, filamentous fibers and whiskers are in situ formed in the samples with addition of CMP, which result to the improvement of the cold modulus of rupture and cold crushing strength. When the addition of CMP is 6 wt.%, the high temperature modulus of rupture increases by 231%, the thermal shock resistance increases by 77% after thermal shock by water cooling 5 times and the percentage of the slag resistant area reduces by 37.2%.     

CuMgAl类水滑石的制备和表征

用盐-碱制备法合成了CuMgAl三元类水滑石化合物。探讨了原料配比、合成方式、水热处理温度和时间对合成过程的影响,筛选出合成HTLcs的适宜条件,并对HTLcs结构的热稳定性进行初步研究。结果表明,制备HTLcs主要取决于pH值,同时由于Cu2+的姜-太勒效应,合成结构单一的CuMgAl类水滑石要求原料配比中n(Cu)∶n(Mg)不得超过1.0,CuMgAl-HTLcs热稳定性较差,300℃焙烧2h结构破坏,600℃开始烧结,在300~500℃之间,随焙烧温度提高所得复合氧化物比表面积增大,最高可达200 m2/g。     

Dynamic modes of Ti combustion in a coflow of N<Subscript>2</Subscript>-Ar mixture

Combustion of bulk density Ti powder (containing 20 wt % TiN as a diluent) in a coflow of N₂-Ar mixture was investigated upon variation in the nitrogen content of the gaseous mixture. The obtained data are believed to open up new horizons for fabrication of layered and composite ceramics by infiltration-mediated combustion.      

粘土矿物用于乙烯聚合催化剂的研究 Ⅰ.以凹凸棒石粘土为载体的乙烯聚合催化剂

研究了以凹凸棒石粘土为载体,负载TiCl4制备的乙烯聚合催化剂的结构、性能及制备规律。结果表明,催化剂中Ti的负载量随焙烧温度的提高而逐渐降低,聚合活性随焙烧温度的提高呈上升趋势,但过高的焙烧温度也会导致粘土晶体结构的彻底破坏而不利于活化粘土活性的提高;通过采用烷基铝等有机金属化合物处理粘土同样可以极大地改善粘土性质,提高催化活性。不同助催化剂对以凹凸棒石粘土为载体的催化剂的聚合性能有较大影响。     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

注射成形粘结NdFeB磁体:工艺·性能·应用

综合介绍了几种适于注射成形粘结NdFeB磁体的磁粉制备方法及特点；讨论了粘结剂、改性剂及磁场取向对注射成形NdFeB磁体最终磁性能的影响及其应用市场。在此基础上，指出了今后开展研究工作的方向。     

籼米淀粉超微粉体的制备及其性质

研究了籼米淀粉超微粉体的一种新的制备方法 ,通过正交实验确定了酶处理淀粉的最佳条件 ,考察了淀粉的溶解度和膨润力。结果表明 ,酶处理淀粉的最佳工艺参数为 :水解温度４５℃ ,时间为２５ｈ ,酶用量为水解淀粉的４５%。随着粒径的减小 ,淀粉的溶解度增大 ,膨润力下降。     

化学还原法制备纳米铜粉的研究

本文采用KBH4在液相中化学还原CuSO4,并加入KOH和络合剂EDTA ,制得了纳米级的纯净的铜粉 ,通过调整反应物的浓度 ,可以消除Cu2 O等杂质。制备的纳米铜粉还存在一定程度的团聚 ,需试验加入分散剂来改善。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

超细粉碎技术现状及发展趋势

综述了国内外超细粉碎技术及设备的现状、进展,指出了其发展趋势,从工作原理、结构特点等方面详细介绍了超细粉碎典型设备,同时又指出了近年来国内外在此领域中的新进展,基于现存问题指出了今后超细粉碎研究的方向。