Dynamic-mechanical properties of polybutadiene rubbers

The dynamic properties of high-cis (98%) and cis-trans (42% cis) polybutadienes, crosslinked with 0.1 to 1.0% of crosslinking agent, have been studied using a torsion pendulum method over the temperature range ?170 to +20°C. For the high-cis rubber plots of damping factor (tan δ) against temperature showed the expected peak in the glass-transition region with an additional peak in the neighbourhood of 0°C attributable to crystallization. The cis-trans rubber showed two damping maxima in the transition region, separated by 30 to 40°C (depending on the degree of crosslinking), suggesting incipient phase separation of the component structures. The rebound resilience of the high-cis rubber at room temperature exceeded that of the cis-trans, reaching 92% at the highest crosslink density. Plots of resilience versus temperature for both rubbers showed a single minimum in the glass transition region.     

农电企业降损节能工作的探讨

阐述了农网降损节能的意义和技术上，管理上的有效措施，指出在线损管理中，只有将理论计算，准确统计，科学分析，营业管理和严打窃电等一系列办法有机地结合起来，才会有良好的效果。     

罐装食品用电镀锡板的耐蚀性及其试验方法

综述了影响罐装食品用电镀锡板耐蚀性能的因素及其试验方法。     

Electrical Resistance Measurement of Glass Transition and Crystallization Characteristics of Zr—Al—Cu—Ni Metallic Glasses

In this paper,glass transition and thermal stability of the Zr-Al-Cu-Ni metallic glasses were investigated by using electrical resistance measurement(ERM),DSC and X-ray diffraction techniques.The experimental results show that the ERM is capable of detecting the glass transition of the amorphous alloys and can help to distinguish the crystallization products of the Zr-Al-Cu-Ni metallic glasses owing to the difference of the electrical resistivity between the precipitation phases.     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

钢铁表面黑色转化膜处理技术

黑色转化膜技术是目前较为先进的钢铁表面处理技术 ,本文试验研究了一种新工艺 ,提出了TB值的概念 ,通过控制TB值即可控制处理液的质量 ,获得性能优良的转化膜。此工艺性能可靠 ,可操作性强 ,并可应用于激光热处理前的预处理。     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

Development of ultra light magnesium-lithium alloys

Magnesium-lithium alloys are among the lowest density metallic materials. Addition of lithium, with a relative density of 0·53, in magnesium reduces the density of the alloy significantly. Furthermore, addition of nearly 11 wt.% lithium converts hexagonal close packed structure of pure magnesium to a body centered cubic lattice, markedly improving formability of the alloy. The development of these alloys, however, had been hampered due to the high reactivity of lithium and magnesium in the molten state and also, due to poor creep resistance and instability of mechanical properties at room temperature. In an attempt to indigenize these ultra light alloys for possible applications in Indian satellite programme, detailed research work was initiated in DMRL. The difficulties associated with producing sound cast ingots have been overcome by controlling melting and casting parameters of these alloys. Extensive work has been done on structure-property correlation of alloys with varying lithium content and minor alloying additions. Based on these work, advanced magnesium-lithium alloys have been developed with improved tensile properties, room temperature stability and creep resistance. Wrought products (plates/sheets) of magnesium-lithium alloy have been supplied to ISAC, Bangalore and are being used in their INSAT-2 programme. This paper describes the systematic studies carried out in the laboratory to indigenize these ultra light alloys.     

用于频率合成器的低损耗声表面波滤波器

简述了产生声表面波滤波器插入损耗的主要机理和获得低损耗的原则；介绍了根据此原则对１００～５００ＭＨｚ５种滤波器的研制过程和结果。实验表明，采用镜像阻抗连接换能器结构可达到３～４ｄＢ的低损耗，并成功地应用于频率合成器中。