Hydrolytic stability and protective properties of polyurethane oligomers based on polyester/ether/polyols

The present study deals with effect of the type and chemical character of incorporated polyester/polyether blocks on the hydrolytic stability of crosslinked polyurethane oligomers. Diffusion parameters of the investigated polyurethane oligomers, giving information concerning chemical changes taking place in neutral, basic and acidic aqueous environments, have also been determined.     

Dynamic-mechanical properties of polybutadiene rubbers

The dynamic properties of high-cis (98%) and cis-trans (42% cis) polybutadienes, crosslinked with 0.1 to 1.0% of crosslinking agent, have been studied using a torsion pendulum method over the temperature range ?170 to +20°C. For the high-cis rubber plots of damping factor (tan δ) against temperature showed the expected peak in the glass-transition region with an additional peak in the neighbourhood of 0°C attributable to crystallization. The cis-trans rubber showed two damping maxima in the transition region, separated by 30 to 40°C (depending on the degree of crosslinking), suggesting incipient phase separation of the component structures. The rebound resilience of the high-cis rubber at room temperature exceeded that of the cis-trans, reaching 92% at the highest crosslink density. Plots of resilience versus temperature for both rubbers showed a single minimum in the glass transition region.     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

用屏蔽暂堵技术封堵水平井裂缝性漏层

克拉玛依油田HW702水平井的大斜度段和水平段,将穿越纵向裂缝发育的二叠系佳木河组储层。为安全钻进和保护油层,用超细碳酸钙和磺化沥青复配后加入复合离子钻井液中成屏蔽暂堵的堵漏钻井液。室内用岩心试验,屏蔽暂堵后渗透率可降为0,暂堵深度小于3cm,可用酸化和射孔解堵。现场使用效果也很好,使HW702水平井顺利完钻,并获得工业油气流。     

MODELING WATER LOSS DURING FRYING OF POTATO STRIPS: EFFECT OF SOLUTE IMPREGNATION

The effect of solute impregnation on water loss and oil uptake during potato strip frying was studied. Blanched potato strips were impregnated at 25°C by soaking in a solution of sucrose-NaCl-water, 20-5-75% by weight. After rinsing and air drying, strips were deep fried in sunflower oil at 160, 170 and 180°C. A control treatment, consisting of potato strips blanched but not soaked and later air dried was also conducted. Solute impregnation provided a decrease of the oil uptake. Two models, based on Fick's law were used to describe water loss during frying. The first one is the classic model with an effective moisture diffusion coefficient assumed a constant value. The second model considers that diffusion coefficient varies during the frying process. For a given frying temperature, constant diffusion coefficient for control potatoes resulted in lower values than the impregnated ones. The variable diffusivity model showed a two-stage behavior: during the first stage of frying, diffusion coefficient increased with frying temperatures, but from a given time on an inverse behavior began. This last fact was found to be related to an increase of the measured peak force needed to penetrate the potato crust.     

FEM model of the ohmic resistance of IP-SOFCs

In the present work, the ohmic resistance of an integrated planar-SOFC (IP-SOFC) has been evaluated by developing a model whose equations have been solved numerically through an FEM method. The model allows to estimate the distribution of voltage and current density in the cell. A comparison between simulated and experimental data of area specific resistance is reported, which shows satisfactory agreement. The mathematical model has also been used to carry out some parametric studies for optimisation purposes. Indeed, a reduction in cell pitch length and an increase in electrode thickness are predicted to lead to a reduction in ohmic losses in IP-SOFCs.     

冷却水污垢及其对冷却器换热的影响

分析了冷却器的结垢机理 ,提出了冷却器污垢层、污垢热阻随运行时间的规律 ,以及污垢热阻与换热系数、换热面积的关系式 ,并通过算例阐述了污垢热阻对冷却器的影响程度 ,进而定性地分析了污垢热阻对空分装置的影响。     

小议变动成本法的合理性

企业对盈亏临界点的计算通常是以变动成本法为基础，但也有以制造成本法为计算基础的，对于这两种成本方法计算的几种盈亏临界点的情况，本文结合案例，通过比较分析认为：盈亏临界点的计算应当以变动成本法为基础更为合理。     

一种T形高压输电线路故障测距新方法

对T形线路的故障测距，现有方法都是先判断故障支路，再将3端线路等效成2端线路进行测距。但在 T节点附近短路，尤其是经高阻短路时，现有的测距方法由于无法正确判别故障支路而存在一定范围的测距死区。针对上述缺陷，分别假设故障发生在某一支路，由假定正常的2段支路端的电压、电流推算求得 T节点电压和注入假定故障支路的电流，从而分别求得3个故障距离。经证明，求得的3个故障距离有且仅有1个在0和对应支路总长度之间，该距离就是真实的故障距离，故障发生在对应支路上。该方法无需事先判别故障支路即可测距，在 T节点附近经高阻故障时无测距死区。其测距精度理论上不受过渡电阻和故障类型影响，无需故障前数据，且对滤波无高要求。EMTP仿真结果表明该方法正确、有效，测距精度高。