Vapor absorption by LiBr aqueous solution in vertical smooth tubes

Heat and mass transfer in a falling film vertical in-tube absorber was studied experimentally with LiBr aqueous solution. The presented results include the effect of solution flow rate, solution subcooling and cooling water temperature on the absorption in a smooth copper tube 16.05 mm I.D. and 400 mm long. The experimental data in the previous report for a 1200-mm-long tube was also re-examined and compared. It was demonstrated by the observation of the flow in the tube that the break down of the liquid film into rivulets leads to deterioration of heat and mass transfer at lower film Reynolds number or in longer tubes. An attempt to evaluate physically acceptable heat and mass transfer coefficients that are defined with estimated temperature and concentration at the vapor–liquid interface was also presented.     

WAVE INTERACTION WITH PERFORATED CAISSON BREAKWATERS

The reflection coefficient of perforated caissons and the total horizontal forces acting on them were experimentally and numerically analyzed and discussed when wave propagates normally. To consider the viscosity effect of fluid and nonlinear action of waves on structures, the VOF (Volume Of Fluid) method combined with the k-ε turbulence model was used to simulate the interaction between waves and structures. Governing equations were solved with the finite difference method. Through 2D experimental study in the wave flume, the empirical relationship between the reflection coefficient of perforated caissons and the main affecting factors were obtained from the experimental data using the least square method. Also the correlation between the ratio of the total horizontal force acting on perforated caisson and the force acting on solid caisson and the main affecting factors were regressed from the experimental data.     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.     

油井参数对超声透射系数的影响

为了研究油井各参数对超声波透射系数的影响，根据超声波在媒质中的波函数和边界条件，求出了油井中超声波的透射系数。当井液和水泥层的声速和密度增大时，超声波的透射系数也随之增大，但变化幅度不大，特别是水泥层密度对超声波的透射系数影响很小；当岩层的声速增大时，超声波的透射系数会出现一个极大值；岩层密度对超声波的透射系数影响较大，且随岩层密度的增大超声波的透射系数随之降低。     

Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.     

Prediction Model for BTA Deep-Hole Machining using Fuzzy Clustering Approach: Experimental Study

In this article, a subtractive clustering-based fuzzy identification method and a Sugeno-type fuzzy inference system are used for modeling in metal cutting. This approach is considered with its application on the experimental study of Boring and Trepanning Association (BTA) deep-hole drilling. The model for the surface roughness is identified by using the cutting speed and feed as input data and roughness as the output data. Using subtractive clustering in both input and output spaces performs the model-building process. Minimum error model is obtained through enumerative search of clustering parameters. The fuzzy model obtained is capable of predicting the surface roughness for a given set of inputs (speed and feed). Therefore, the operator can predict the quality of the surface for a given set of working parameters and will then be able to set the machining parameters to achieve a certain surface quality. The fuzzy model is verified experimentally by further experimentation using different sets of inputs. The tool life is also investigated using the same approach. The fuzzy inference system obtained is capable of predicting the tool life for a given set of cutting parameters. Therefore, the operator will be able to predict how many minutes the cutting tool is going to last and will set the time for the next tool change.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

甲基叔戊基醚合成反应的热力学分析

利用戊烯与甲醇合成甲基叔戊基醚(TAME)反应的热力学平衡实验数据, 选择不同的混合活度模型,分别计算得到了该反应体系的平衡常数,并与理论计算得到的平衡常数相比较,筛选出了适合该反应体系的活度计算模型.     

应用AR模型的IMU误差系数漂移预测研究

将影响IMU误差系数漂移并难于分离的多种因素综合为一种因素，假定IMU误差系数的漂移由一特定系统所引起，从而采用时间序列建模方法进行IMU误差系数漂移的预测。该方法具有消除各因素具体分析中的不确定性并减少其工作员的优点。文中描述了其原理，对某惯组的33个误差系数进行了时间序列建模与预测并得到有效的结果。最后还阐述了存在的问题及其解决方法。