黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Effect of flow on solutions of rod-coil block co-polymers

An elongational flow field is imposed on a solution of block copolymers consisting of semirigid macromolecules with rigid, rodlike sequences of units in combination with random coil (flexible) units. The problem is formulated according to the lattice treatment of Matheson and Flory. In this formulation, the system consists of rigid blocks whose lengths and locations are fixed by the structure within each macromolecule. These blocks are separated by random coiled units. An excess free energy other than the equilibrium Gibbs free energy of the quiescent solution has to be considered due to the flow field that tends to align the rods. This excess free energy is calculated from the potential energy of rods when a steady-state, homogeneous and irrotational flow field is applied to the solution. The effects of composition, polymer-solvent interaction, size of the co-polymer and flow rates are investigated. Depending on the size and number of rods, some of the chains studied exhibit a biphasic region at equilibrium that shifts to lower concentrations with increasing flow. Longer chains with shorter rods that are isotropic at equilibrium, exhibit a biphasic region at finite values of flow. The degree of orientation increases sharply when the system is biphasic. For larger flows, the orientation function is very close to unity which is perfect orientation.     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

A new adaptation of mapping method to study mixing of multiphase flows in mixers with complex geometries

The main objective of the present work is to modify the traditional mapping method for the simulation of distributive mixing of multiphase flows in geometries involving moving parts such as, internal mixers or twin-screw extruders without a limitation on their geometrical periodicity. The periodicity condition, limits the results of traditional mapping method to tracking mapping mesh between specific discrete time intervals or distances for that geometry is repeated, hence, result is only for fixed orientation of rotors. Imaginary domain method is introduced to track mapping mesh from one state to the next free of geometrical periodicity limitations. In this work the method is introduced and its applicability and accuracy is discussed in details. A two-dimensional (2D) simulation of mixing of two Newtonian fluids with different viscosities in an intermeshing internal mixer is used as a test case study. In this example the key issues of ability to predict mixing state in details for all orientations of rotors is presented. To reduce diffusion errors of mapping method in the boundaries of the rotors, mapping mesh refinement technique that relies upon one single reference mesh is also presented.     

Drag coefficient of flow around a sphere: Matching asymptotically the wide trend

An empirical relationship of drag coefficient of flow around a sphere is developed for the entire range of Particle Reynolds numbers reported in the literature from Stokes regime to the condition when turbulent boundary layer prevails. The relationship is obtained using an approach to match asymptotically the wide trend of drag coefficient. The matching approach, which relies on dividing the wide trend into smaller segments that can be combined into an overall relationship, employs regression techniques and thus warrants the best-fit accuracy results. The relationship is calibrated with experimental data available in the literature covering the entire range for Reynolds numbers up to ~ 10⁶. For Reynolds values greater than 10⁶, the relationship renders a drag coefficient of 0.2. The performance of the relationship is tested and compared with other suitable models found in the literature. This relationship is also transformed into an explicit expression for settling velocity calculations.     

Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.     

EXPERIMENTAL AND NUMERICAL INVESTIGATIONS ON HORIZONTAL OIL-GAS FLOW

Experiments were carried out to investigate the characteristics of oil-gas flow in a horizontal pipe on a large scale (with the inner diameter D = 125 mm). With the experimental data, the flow patterns were presented. Through the analyses for the flow regime transition, it was found that there was a critical superficial velocity of liquid phase for the flow regime transiting from stratified flow to slug flow. The slug flow could not occur until the superficial velocity of liquid phase was higher than the critical velocity. For the flow pattern transiting from stratified to slug flow, the transmitting velocity of gas phase decreases with the augmentation of superficial velocity of liquid phase. On the basis of the experiments, numerical simulations of different flow patterns and their transitions were performed with the use of the Volume Of Fluid (VOF) technique. The results of the computations are shown to match well with the measured data in the experiments.     

矩形垂直筛板的流体力学性能研究

在600mm的有机玻璃冷模塔中,用水-空气体系测定矩形垂直筛板的塔板压降、漏液和雾沫夹带等流体力学性能,确定了合理的塔板结构,使其具有较高的气液通量和较宽的操作范围,空塔动能因子最大可达3.0kg1/2(m1/2.s)-1,液流强度可达21.6m3/(m.h)。并对不同气液流量下塔板的流体力学实验数据进行关联和分析,得出了矩形垂直筛板的干板压降计算关联式以及漏液率随液流强度和空塔动能因子的变化关系,为矩形垂直筛板的设计提供了依据。与新垂直筛板相比,矩形垂直筛板具有更低的塔板压降。     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005