钨金属化与氧化铝陶瓷高温共烧

阐述了钨金属化与氧化铝陶瓷高温共烧工艺的特点,分析了烧结过程中温度曲线和露点等工艺参数对钨金属化与瓷件结合强度、密封气密性和收缩率的影响。通过反复的试验和烧结机理分析对比,给出了最佳的控制参数。     

膜分离法回收合成氨弛放气中氢气

介绍了膜分离的原理和应用。实践表明该方法具有效率高、流程简单、操作灵活容易、纯度高和收率高等优点。     

硫酸铵-氯化亚锡-孔雀绿体系浮选分离铂

研究了在盐酸介质中硫酸铵存在下氯化亚锡—孔雀绿—水体系浮选分离铂的方法。在最佳实验条件下，铂的浮选率可达100．0％，并与常见贱金属完全分离。     

某难选铅锌矿石浮选分离新工艺试验研究

针对某难选铅锌矿的矿石性质，进行了较为系统的小型试验研究。结果表明：在铅循环中采用Bx SN—9^#组合捕收剂、石灰 ZL—01组合抑制剂，在锌循环中采用捕收剂磁处理浮选技术等措施，可以较好地解决该难选矿的浮选分离问题。     

HPD-2型非临氢降凝催化剂工艺实验

利用HPD-2型非临氢降凝催化剂进行了中试实验。结果表明：HPD-2型非临氢降凝催化剂相对其他的同类催化剂产品液体收率较高，最高可达95％以上；在反应温度为380℃时，凝点降幅在50℃左右，降凝效果较好；产品性质稳定，具有很好的应用前景。     

PVT Measurements on tetrafluoroethane (R134a) along the vapor-liquid equilibrium boundary between 288 and 373 K and in the liquid state from the triple point to 265 K

For the investigations of the gas-liquid phase equilibria, a new apparatus has been developed capable of simultaneously determining the pressure and the liquid and vapor densities using Archimedes' principle. The relative measurement uncertainties of the liquid and vapor densities of R134a (purity, 99.999%) at 313 K are 2×10^–4 and 7×10^–4, respectively (95% confidence level). For the measurements in the liquid region along nine quasi-isochores at pressures up to 5 MPa, an isochoric apparatus was used. The relative measurement uncertainty ofpv/(RT) is less than 1×10^–3. In addition to the investigation of the (p, v, T) properties, the temperature and pressure at the triple point and the vapor pressure between the triple point and 265 K were measured. On the basis of these data, a vapor pressure correlation has been developed that reproduces the measured vapor pressures within the uncertainty of measurement. The results of our measurements are compared with a fundamental equation for R134a, which is based on the measurements of other research groups.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.     

激光微焊接质量的模糊识别技术研究

讨论了激光微焊点焊接质量的模糊识别的概念，数学模型及其应用方法，并介绍了系统的硬件组成。     

电分标准工作曲线的推导与实践研究

本文根据人眼视觉特性、孟塞尔方程及彩色复制理论,并结合实际工艺路线和工艺条件,推导出标准阶调复制曲线和标准电分工作曲线。它与德国Hell公司所绘的电分标准工作曲线基本一致。并做到了各工序有数据,有质量标准,使平印制版做到有规可循。     

循环流液相等电聚焦方法及应用研究

利用循环流液相等电聚焦技术，对Ｈｂ、Ｃｙｔ．Ｃ和ＢＳＡ混合物进行分离，对ＲＮａｓｅＡ粗制品进行精制。该方法上样量大，活性回收好。对聚焦过程中扩散、对流和电渗的影响进行了讨论。