CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

一个基于相邻像素兼容度的模糊加权平均滤波器

在文献[1]的基础上，提出几个改进的模糊加权平均滤波器。本文的方案不仅同时考虑了相邻像素对中心像素的兼容性以及中心像素对相邻像素的兼容性，而且还考虑到了权系数对局部环境的适应性。实验结果表明，该方法相比文献[1]中的模糊加权平均滤波器以及标准的均值滤波器、中值滤波器在噪声消除与边缘保留方面具有更好的性能。     

Prediction Model for BTA Deep-Hole Machining using Fuzzy Clustering Approach: Experimental Study

In this article, a subtractive clustering-based fuzzy identification method and a Sugeno-type fuzzy inference system are used for modeling in metal cutting. This approach is considered with its application on the experimental study of Boring and Trepanning Association (BTA) deep-hole drilling. The model for the surface roughness is identified by using the cutting speed and feed as input data and roughness as the output data. Using subtractive clustering in both input and output spaces performs the model-building process. Minimum error model is obtained through enumerative search of clustering parameters. The fuzzy model obtained is capable of predicting the surface roughness for a given set of inputs (speed and feed). Therefore, the operator can predict the quality of the surface for a given set of working parameters and will then be able to set the machining parameters to achieve a certain surface quality. The fuzzy model is verified experimentally by further experimentation using different sets of inputs. The tool life is also investigated using the same approach. The fuzzy inference system obtained is capable of predicting the tool life for a given set of cutting parameters. Therefore, the operator will be able to predict how many minutes the cutting tool is going to last and will set the time for the next tool change.     

从图像的二维谱分析现行电视的缺陷

从图像的二维谱可以得出现行广播电视图像为什么不能满足人眼的视觉匹配以及现行电视制度的不足 ,从而对未来的高清晰度电视发展提出要求。     

基于VXI总线的超宽带线性调频信号源的设计

主要介绍了VXI总线C尺寸超宽带线性调频信号源的设计方法，重点描述了利用现场可编程逻辑器件FPAG和DSP设计VXI总线接口电路，以及数字波形存储直读技术在线性调频信号源中的应用。     

Fifty Years On: Brown v. Board of Education and American Psychology, 1954-2004 An Introduction.

Introduces the current issue of the American Psychologist, which examines the ramifications of the Brown vs. Board of Education decision and its sequelae over the last 50 years, with a special focus on the mixed role of psychological research and practice. Despite the great strides toward a more just society since May 17, 1954, inequities remain in schooling, in social relations, and in economic opportunity. How will history judge American psychology 50 years from now vis-a-vis the possibilities it helped create via Brown? The articles in this special issue suggest several important directions of research and action our field will need to take if the verdict of history is to be a positive one. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

企业中层管理人员培训的思考

以分析企业中层管理人员培训的现状为突破口,阐述了中层管理人员培训需求分析的思路和方法。在此基础上对培训内容进行整体设计,指出针对此类培训应采用的培训方式和评估方法。以期对企业中层管理人员的培训起到一些启发和借鉴作用。     

无机阻燃剂高聚合度聚磷酸铵的研制

以五氧化二磷、磷酸铵盐、尿素为原料、氨气为保护气,制备了高聚合度聚磷酸铵无机阻燃剂。考察了五氧化二磷、磷酸铵盐、尿素的用量和反应温度对聚磷酸铵平均聚合度的影响。采用端基滴定法测定了聚磷酸铵的聚合度,并用X射线衍射(XRD)法表征了聚磷酸铵的晶体结构,同时测定了聚磷酸铵的粒度和溶解度。实验结果表明,制备聚磷酸铵的最佳反应条件为:n(磷酸氢二铵)∶n(五氧化二磷)∶n(尿素)=1∶1∶0.3,反应温度280~300℃,反应时间40m in,热处理温度250~280℃,热处理时间110m in。在此条件下制备的聚磷酸铵的平均聚合度大于600,平均粒径直径小于50μm,在水中的溶解度小于0.4g;XRD表征结果表明,所合成的物质为Ⅱ型聚磷酸铵。     

烟气轮机叶片应力分析与寿命评估方法评述

烟气轮机是炼油厂催化裂化装置的关键设备,合理预测叶片疲劳寿命是保障烟机安全运行的有效手段。从力学建模和边界条件两个方面简要阐述了叶片的应力分析方法,并系统分析了影响烟机叶片疲劳寿命的主要因素,提出了利用改进的局部应力应变法进行叶片寿命预测的合理性和叶片疲劳寿命的评估方法。