基于有限元分析的金刚石钻头强度验算公式

在对81／2B125金刚石钻头进行有限元计算分析后，找出最大应力点在金刚石钻头冠部切削告处。通过改变各相关尺寸和结构型式，用有限元法模拟试验过程，在给定结构参数和工艺参数情况下获得多组数据。根据专业知识，参考有限元计算获取的各组数据变化特征，选出拟合较好的公式类型，再采用回归分析方法确定待定系数，最后得出工程上实用的金刚石钻头强度验算公式。用这个公式对81／2B461W和121／4B331金刚石钻头进行了强度验算，经改进设计后钻头在现场使用取得了良好的效果。     

HSLA-80/100钢的焊接

对ＨＳＬＡ－８０／１００钢的焊接性、焊接材料及焊接工艺进行了综述，并指出了现存在的主要问题。     

Effects of shear flow on long-ranged correlations,spinodal demixing kinetics,and the location of the critical point and cloud point

A derivation of an expression for the shear rate-dependent Ornstein Zernike structure factor is discussed, together with the resulting anomalous behavior of the turbidity. The predicted scaling behavior of the turbidity, comprising the effect of both temperature and shear rate, is in good agreement with experiments on binary fluids. Then initial spinodal decomposition is discussed, and an explicit expression for the time- and shear rate-dependent effective diffusion coefficient is derived, which shows all the typical characteristics of anisotropic light scattering patterns that are observed experimentally for binary fluids. Next it is shown that the spinodal is shifted linearly with the (bare) Peclet number for not too large Peclet numbers, whereas the cloud point is singularly displaced into the unstable region due to a shear now. This is in agreement with an experiment on a two-polymer/solvent mixture and binary fluid mixtures. It is argued that light scattering is useless to determine the location of the spinodal of a sheared system.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

结构强度储备的评估及结构维修过程的跟踪决策

本文提出了已建成结构在服役过程中构件的强度储备比和结构整体的强度储备比的概念和定义,它们都是随结构使用和维修过程而变化的时间的函数。我们建议以实际的强度储备比作为构件和结构服役安全度的表达方式,给出了构件和结构强度储备比的具体评定方法,并以结构整体的强度储备比作为控制参数决策结构的维修过程,以求得结构全寿命维修的优化控制。本文所提出的方法适用于具有良好的结构重分析程序和精密细致的检测手段的工程。一般重要的结构工程,例如核电站、海上结构、航空航天设备等均具备上述条件。因而本文所提的方法非常实用,可以立即应用于重要的工程项目,具有重大的经济和社会效益。     

Recursive solution of inverse natural convection problems by means of mode reduction

 A recursive method based on the Kalman filtering is developed to solve inverse natural convection problems of estimating the unsteady nonuniform wall heat flux from temperature measurements in the flow. By employing the Karhunen–Loève Galerkin procedure that reduces the Boussinesq equation to a small set of ordinary differential equations, the computational difficulties associated with the Kalman filtering for the partial differential equations are overcome. The present method is assessed through several numerical experiments, and is found to yield satisfactory results. Received 20 January 2001 / Accepted 31 May 2001     

也谈轻型钢结构房屋柱基设计

对柱脚抗剪键的设置和计算中所取用的荷载组合提出个人观点,同时对轻钢结构柱脚螺栓受拉计算提出注意事项.     

A novel laboratory bench for practical evaluation of catalysts useful for simultaneous conversion of NOx and soot in diesel exhaust

This study deals with the development of a laboratory bench for the practical evaluation of catalysts that are useful for the direct conversion of NO_x and soot in the exhaust of diesel engines. The employed model exhaust is generated by using a diffusion burner with additionally dosing some gaseous components to the burner gas to obtain a realistic feed composition. The produced soot is extensively characterized by employing thermogravimetry, transmission electron microscopy, N₂ physisorption and temperature programmed techniques. The results of the different characterization methods show that the present soot is suitable for the intended catalytic investigations. The simultaneous conversion of NO_x and soot is examined like in practice, i.e. the soot is separated from the tail gas by a diesel particulate filter (DPF) that is coated with the catalyst. The deposited soot is then catalytically converted by NO_x and O₂ to form N₂ and CO₂. The conversions of NO_x and soot are measured by exclusively applying gas analysers, whereby a special experimental procedure is developed to determine the soot removal. Hence, additional soot related analytics are not required. To show the suitability of the constructed bench a Pt/Fe₂O₃/β-zeolite sample is taken as test catalyst that is reported to be very active in NO_x/soot reaction. The measurements performed with and without catalyst clearly show the effect of the used sample in simultaneous NO_x/soot conversion. We therefore consider the constructed laboratory bench to be a useful tool for testing and ranking catalytic materials.     

Reducing Average and Peak Test Power Through Scan Chain Modification

Parallel test application helps reduce the otherwise considerable test times in SOCs; yet its applicability is limited by average and peak power considerations. The typical test vector loading techniques result in frequent transitions in the scan chain, which in turn reflect into significant levels of circuit switching unnecessarily. Judicious utilization of logic in the scan chain can help reduce transitions while loading the test vector needed. The transitions embedded in both test stimuli and the responses are handled through scan chain modifications consisting of logic gate insertion between scan cells as well as inversion of capture paths. No performance degradation ensues as these modifications have no impact on functional execution. To reduce average and peak power, we herein propose computationally efficient schemes that identify the location and the type of logic to be inserted. The experimental results confirm the significant reductions in test power possible under the proposed scheme.     

关于混凝土钻芯取样法有关标准的讨论

本文对国内不同行业有关混凝土钻总取样方法的标准进行了讨论，供月行在使用和修订相应标准时参考。     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.