用试井方法确定注水后地层渗透率的变化

大港油田已进入开发中后期，高含水油田占73％，开发初期的一些参数已不适合现在开发的需要。研究出一套用试井方法确定注水以后地层渗透率变化的方法，对大港油田的增储上产具有重要意义。     

On the hollowness ratio effect on the dynamics of a spinning Rayleigh beam

The analytical solutions of a spinning Rayleigh beam with rotatory moment inertia and gyroscopic effect are presented in this paper. The critical speeds can be written analytically in a function of the length-to-radius ratio (l) defined by the beam's length over its outer radius and the hollowness ratio (α) defined by the hollow area over the total area of the cross section. The sensitivity analyses show that the critical speed is decreasing with l, but increasing with α. Moreover, α is more sensitive to the critical speeds. The design of a spinning beam should therefore be emphasized more on the hollowness factor. Contrary to common belief, only finite critical speeds exist and the number is independent of the boundary conditions. It increases monotonically with l, but decreases with α. The steady state unbalanced response can therefore be expressed analytically by the finite precessional modes and the corresponding generalized coordinates.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

复合沉淀氯化镨钕工艺研究

针对草酸沉淀成本高的问题，提出了复合沉淀的方法，试验结果及生产应用都证明了此方法能达到降耗同效的目的。     

降低氧化铝生产中熟料折合比的探讨

在氧化铝生产过程中，熟料折合比是烧结法一项重要的综合性指标，本文通过对熟料折合比的定义、计算公式的剖析，分析了生产过程中影响熟料折合比的主要因素，对有效降低熟料折合比的措施进行了探讨。     

房间空调器高效节能技术分析

本文主要介绍了高效节能型空调器的优化设计，包括选用高效压缩机、增大换热面积，增大风量、管路的合理设计，旨在提高制冷量，降低功耗，提高能效比。     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。     

基于自然地理形态的道路测设及其曲线方程的拟合

在山区村镇及风景旅游名胜区的建设中，其道路的曲线测设，往往要基于自然地理形态进行，也就是路径的选择，有时具有不可选择性，且要求与实地具有最大的符合性。因此，其测设的作业方法不同于一般意义的道路测设；其曲线方程的建立，也是极其困难的。本就基于自然地理形态的道路测设工作的曲线类型的选择、曲线的拟合方法、曲线方程的建立及其数据的计算，提出了利用CAD技术进行曲线拟合、曲线方程的建立、曲线计算的实用技术方法。     

可焊性高强度钢筋的开发与生产

为进一步开发国际钢材市场，研制开发了符合加拿大可焊性高强度钢筋标准要求的高强度钢筋．制定了化学成分及力学性能内控标准，分析了生产工艺各环节对成分和性能的影响，依据试验结果，在全面统计分析的基础上，调整了冶炼成分，生产的531批钢筋全部合格．通过直方图及回归分析，说明了制定的产品生产工艺可行，也为今后的生产提供了理论依据。     

苯乙烯与1-(2-叔丁基过氧异丙基)-3-异丙烯基苯共聚行为研究

苯乙烯与1－（2－叔丁基过氧异丙基）－3－异丙烯基苯（D120）能进行自由基共聚合反应，聚合后过氧基团以侧基的形成被保留在共聚物大分子链上，凝胶色谱分析发现，随原料单体中D120比例增加，共聚物的分子量减小，分子量分布变窄，DSC分析发现共聚物中过氧基团的分解温度随D120结构单元含量的增加而下降，但仍高于D120单体过氧基团的分解温度，苯乙烯与D120的竞聚率为：rD120=0.700,rSt=0.714。