试论企业人格化管理的力量因素

论述了影响企业人格化管理的力量因素，并指出制度纪律是其保障因素，道德规范是其自律因素，理想目标是其进取因素。     

锡矿山重复水利用的措施及效果

本介绍了锡矿山前闪星锑业有限责任公司如何加强对关键耗水工序的管理及提高重复水利用率的措施，并对所取得的效果进行了阐述，可供用水大户如何节水以借鉴。     

Three-parameter vs. two-parameter Weibull distribution for pultruded composite material properties

The three-parameter and two-parameter Weibull distributions are compared using 26 mechanical property data sets of fiber-reinforced polymeric (FRP) composite materials manufactured by the pultrusion process. Both strength and stiffness properties were examined. The probability distributions were compared on the basis of goodness of fit, nominal design values, and allowable load to achieve uniform reliability. It is recommended that the two-parameter Weibull distribution be used to characterize FRP composite material properties. The primary basis for this recommendation is small differences in nominal design values and small differences in allowable loads between the two-parameter and three-parameter Weibull distributions. Other supporting reasons for the recommendation are similar observed significance levels in distribution fitting, computational efficiency, and the fact that the location parameter of the three-parameter Weibull distribution is near the first order statistic.     

具有多重PRF的雷达回波脉冲视频仿真电路的实现

在目标回波仿真原理的基础上，给出了一种新颖的脉冲多普勒雷达目标回波视频频脉冲仿真电路。通过计数分频和计数延时技术，该电路获得了大范围可变的脉冲重复频率和高精度的脉冲时延，能对距离不断变化的动目标进行实时模拟。给出了电路的结构框图，并对设计原理作了必要说明。     

一种提高低温流体比体积计算精度的方法

采用了一个既能提高立方型状态方程比体积计算精度，又不影响气液平衡条件的简单摩尔修正项来改进PR方程比体积的计算。本文对19种低温流体给出其修正项的值，计算饱和蒸气和液体比体积，并与未修正的PR方程的计算值比较，结果表明这种修正能显著提高低温流体（包括量子流体氢、氦和强极性的氨气）饱和液体比体积的计算精度，并对蒸气比体积的计算也略有改进。     

层状Ti3SiC2陶瓷的组织结构及力学性能

利用热压烧结TiH₂,Si和C粉获得了致密度大于98%的层状Ti₃SiC₂陶瓷。利用压痕法,在不同的载荷下测定了材料的维氏硬度, 发现其硬度值随载荷的增加而降低,在最大载荷30kg时,硬度值为4GPa。压痕对角线没有发现径向裂纹的出现。 这归因于多重能量吸收机制——颗粒的层裂、裂纹的扩展、颗粒的变形等。利用三点弯曲法和单边切口梁法测定了材料的强度和韧性分别为270MPa和6.8MPa·m1/2。Ti₃SiC₂材料的断口表现出明显的层状性质,大颗粒易于发生层裂和穿晶断裂,小颗粒易被拔出。当裂纹沿平行于Ti₃SiC₂基面的方向扩展造成颗粒的层裂,当裂纹沿垂直于基面的方向扩展时,裂纹穿过颗粒的同时,在颗粒内部发生偏转,使裂纹的扩展路径增加。裂纹的扩展路径类似人们根据仿生结构设计的层状复合材料。裂纹在颗粒内的多次偏转、裂纹钉扎以及颗粒的层裂和拔出等是材料韧性提高的主要原因。此外,在室温下得到的荷载-位移曲线,说明Ti₃SiC₂材料不象其它陶瓷材料的脆性断裂,而是具有金属一样的塑性。     

Simulation and optimization of tool-life in manufacturing centers

This paper presents the development of an optimization and a computer-simulation model to evaluate the process plans of a manufacturing center by analyzing the effect of tool failure on system performance. The GPSS/PC simulation program that is used in this study has been built with variables, functions and matrices so that many experiments could be conducted with the model. Sensitivity analysis is presented and the developed model has proven to be useful in determining optimum sequencing of parts for various operating policies.     

人支气管上皮靶细胞形态学参数的测量

支气管上皮靶细胞形态学参数对计算受氡子体照射的支气管的剂量是很重要的。本文介绍利用奥尔新兰-PAS 染色的外科切除人肺组织切片,测量基底细胞粘液细胞和的胞核深度与数目。结果表明,叶、段和小支气管的粘液细胞核深度分别为相应节段基底细胞的61%、69%和73%;此三节段粘液细胞的数目分别为基底细胞的53%、29%和28%,平均为37%。