面向水环境的传感网虚拟距离覆盖算法

针对水面传感器随机部署时网络覆盖率较低的问题,采用了一种面向水环境的无线传感网虚拟距离覆盖算法,在保证连通性的前提下提高网络的覆盖率。在虚拟距离算法中,每个传感器节点的运动受到3个虚拟距离的影响:节点之间的虚拟距离、未被覆盖区域格点与节点的虚拟距离以及边界与节点间的虚拟距离。仿真结果表明:该算法可以有效地提高网络覆盖率。可以得出以下结论:虚拟距离算法通过对节点位置的控制更新有效提高了网络覆盖率,使节点得到优化部署。     

渠首水位实时调控模型——以船行灌区一支渠为例

很多大中型灌区在输配水过程中存在水位衔接不当的问题,加之田面高程存在起伏,使得灌溉时往往存在部分田面不能上水或受淹等问题。本文提出了空间灌溉率的概念,并利用GIS的三维分析功能研究了其与渠道渠首水位之间的关系。分析表明,空间灌溉率与渠首水位之间的关系符合Logistic曲线;针对船行灌区一支渠,得到该Logistic曲线的参数,并确定了一支渠渠首和干渠渠首不同空间灌溉率所需的水位,为灌区水位实时调控提供基础数据。     

引水工程大流量渡槽结构型式选择

针对工程等级高、过水流量大、抗震设防要求高的引水工程,渡槽结构型式选择存在工程技术难题,根据引水工程渡槽槽墩较高、荷载大、结构断面大、沉降变形影响因素较为复杂特点,进行了渡槽支承型式、槽身截面形式、渡槽墩身的比选。结果表明:简支结构具有减少施工难度和不均匀沉降对槽体结构应力影响,简化结构受力条件,简支结构较为有利优点。空心重力墩具有节省材料,充分利用材料强度,刚度较大,墩身质量较轻,抗震能力和抗冲击强,高度较大优点,对类似工程设计具有参考意义。     

高分子水处理剂的绿色化研究进展

简要介绍了近年来水处理领域在高分子水处理剂产品及生产工艺方面的绿色化研究进展状况。     

油田采出水的精细过滤技术

低渗透油层渗透率〈0．1μm^2，孔喉半径小，容易被堵塞，对注入水质要求高，目前缺乏对含有原油、化学添加剂、粉质颗粒和无机盐的油田采出水适应性强的精细过滤设备。本文介绍了油田采出水回注精细过滤材料试验和采用旋流配水、脉冲水流反洗技术的改性聚四氟乙烯滤芯过滤装置的小试和中试研究情况，研究开发的改性聚四氟乙烯精细过滤装置，当进水含油量〈20mg／L、悬浮物含量〈20mg／L时，出水达到了（《碎屑岩油藏注水水质推荐指标》（SY5329-94）规定的A1级注水水质标准。     

化学接枝法制备腻子型吸水膨胀橡胶研究

吸水膨胀橡胶是一种新型的功能高分子材料,过去多用机械共混的方法制备,但是这种方法存在着反复使用性能差的缺点,针对这个问题,本实验采用过硫酸铵/硫代硫酸钠氧化还原引发体系,有效地使丙烯酸钠单体与天然胶乳接枝共聚,制备出吸水倍率相当高的腻子型吸水膨胀天然橡胶。实验结果表明:反应温度、引发剂用量对吸水倍率和接枝率有明显的影响,单体用量对吸水倍率影响较大;反复吸水能力基本保持不变。     

Synthesis and characterization of superabsorbent hydrogels composites based on polysuccinimide

A kind of novel superabsorbent hydrogel with high swelling ratio property that could be used for the development of water absorbing resin, soil water retention agent, and chemical sand‐fixing material was synthesized in this study. The hydrogels were prepared by the crosslinking reaction of polysuccinimide (PSI). The relationships between swelling ratio and volume of solvent as well as the concentration of crosslinking agent were investigated in detail. Several composites, such as starch, carrageenan, and polyacrylamide, were added into hydrogels to enhance the swelling ratio. It was found that the swelling ratio was significantly increased, which the maximum water absorbency was enhanced 2.46 times when the composite polyacrylamide (PAM) was added compared to the control. The effects of ionic strength and sensitivity of pH on hydrogels were also studied. The modified hydrogels products with swelling ratio less sensitivity to the salinity as well as relative high swelling ration in salinity system were also obtained by adding PAM. Through the Fourier transform infrared spectroscopy (FTIR) characterizations, the crosslinking reaction mechanism and the structure of composite were proposed. In addition, the transmission electron microscopy (TEM) examinations showed that some composite materials elevated the physical crosslinked and connected channels density substantially. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 550–557, 2006     

颗粒活性炭的特性参数与吸附性能的关系试验

采用活性炭进行饮用水的深度处理,选择适合原水水质的活性炭至关重要,通过6种不同颗粒活性炭特性参数的测试,对饮用水有机物的吸附试验以及吸附等温线的测定,结果表明:针对颗粒活性炭的筛选,碘值,亚甲蓝值,吸附等温线的KF及斜率1/n值均不能单独作为评价筛选活性炭优劣的指标,而应综合考虑颗粒活性炭的孔径分布与原水中有机物的相对分子质量分布相匹配等。研究还表明:碘值,亚甲蓝值,吸附等温线的KF存在一定的相关性,从颗粒活性炭的特性参数和吸附性能参数可以推测活性炭滤柱试验吸附效果。颗粒活性炭用于饮用水深度处理,能去除水中相对分子质量小的有机物,处理的水量为颗粒活性炭体积的4800倍时,对CODMn的去除率为15%左右。     

Influence of the pH of Water on its Electron-Accepticity and Donicity

By means of contact angle measurements on dry layers of electrostatically neutral dextran with pure water (pH 6.1), water acidified with HCl (to pH 1.94) and water made alkaline with NaOH (to pH 12.8), it could be shown that there was essentially no change as a function of pH in the ratio of γ⁺/γ^- of water as compared with the aqueous acid and alkaline solutions. (Here γ⁺ is the Lewis acid parameter of the polar surface tension component of water and γ^- is its Lewis base parameter). In contrast, with contact angles measured with the same liquids on negatively charged clean glass, a significant decrease in contact angle was observed with water at pH 12.8, which was caused by the fact that at this alkaline pH an increase in surface hydrophilicity took place. This is because surfaces that have a given surface electrical potential at neutral pH generally acquire an even higher surface potential under more alkaline conditions which, concomitantly, also gives rise to an increase in surface hydrophilicity, and thus to lower contact angles with water. Finally, contact angles with acid water, pure water, and alkaline water, deposited on hydrophobic Parafilm surfaces, were exactly the same.     

Physical characteristics of sweet potato pulp/polycaprolactone blends

Sweet potato pulp (SSP) obtained as a by‐product from starch extraction was blended with polycaprolactone (PCL) to prepare a biodegradable plastic material. In the blends, PCL was used as a reinforcing agent. The SPP/PCL blends were prepared by compression‐molding under high temperature and pressure, at different SPP/PCL ratios, and the mechanical properties of the molded specimens were tested. Matrix structure and thermal properties were measured by using a Fourier transform infrared (FTIR) spectrophotometer, scanning electron microscope (SEM), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). Mechanical properties (tensile and flexural properties) were also measured to find the most suitable ratio in a SSP/PCL blend. During compression molding of the SPP/PCL blends under high pressure and temperature, chemical reaction occurred between SPP and PCL, and thus, thermal stability and mechanical strength of the blends increased and water uptake decreased. Also, by increasing the PCL content in the blend, the matrix in the blend became more homogeneous, and consequently, mechanical strength of the molded specimen increased. At 7/3 or 6/4 weight ratio of SSP/PCL, water uptake of the molded specimen became substantially less than that at 8/2. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 861–866, 2004