SPECTRAL DENSITY ESTIMATION FROM NONLINEARLY OBSERVED DATA

Abstract. The estimation of the spectral density function of a stationary Gaussian process at the input of an instantaneous nonlinearity is considered when the nonlinearity is known and a finite set of observations of the output process is given. A class of spectral estimates is considered and their quadratic-mean consistency is established; precise asymptotic expressions for their bias and covariance are derived and their asymptotic normality is obtained.     

Response of captive lowland gorillas (Gorilla gorilla gorilla) to different housing conditions: Testing the aggression-density and coping models.

Several studies have suggested that primates react differently to spatial reduction. In this article, the authors tested some general hypotheses on primate response to spatial reduction by studying the Apenheul lowland gorillas (Gorilla gorilla gorilla; Apeldoorn, the Netherlands). The frequency of conflicts did not greatly change between the 2 housing settings, thus not supporting the density- aggression model. Indoor, gorillas performed touching behavior more often and increased their level of reconciliation. These findings support the coping model. Indoor, the gorillas also maintained broader interindividual distances by increasing the levels of sitting alone, avoidance, and dismissing behaviors. In conclusion, the Apenheul gorillas modified selectively the distribution of some patterns typical of their behavioral repertoire in response to a high-density condition. Both avoidance and coping tactics were used, thus revealing high levels of behavioral flexibility in this species. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

低松装密度水雾化铜粉工艺的研究

本文研究了氧化 还原法生产铜粉的新工艺 ,该工艺是通过氧化还原将水雾化铜粉加以表面改性 ,形成海绵状的粉末 ,显著降低水雾化铜粉的松装密度 ,这种铜粉既具有电解铜粉低的松装密度 ,又具有水雾化铜粉高的流动性。讨论了氧化时间、氧化温度对铜粉松装密度的影响。本工艺是一种新型环保、节能、可替代电解法生产铜粉的先进工艺     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

特征X射线能谱法测定Fe^＋注入小麦种子的深度

用１１０ｋｅＶ Ｆｅ＾＋离子束垂直注入小麦种胚后，在扫描电子显微镜上沿种子纵沟剖面，在不同深度上测量Ｆｅ元素被激发出的特征Ｘ射线强度分布，结果表明分布呈指数衰减，与晶体中的热扩散分布相类似，并对此进行了讨论。     

二钼酸铵(ADM)非团聚晶体的生成试验

探讨了二钼酸铵非团聚晶体生成的机理及制取新工艺。采取该工艺制取的ADM费氏粒度（Fsss)约30μm，激光粒度分布d0.5为370μm，松装比达1.37/cm^3。     

浅谈多层建筑的斜屋面结构设计

多层建筑的斜屋面结构，应建立合理的结构模型，选用合理的结构方案，在采用结构软件设计时，一定要正确采用倾斜构件沿水平或垂直方向的荷载。     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

Egg white powder in extruded fish crackers

Four levels of egg white powder (EWP), 0, 1.5, 3.0 and 4.5%, were added to fisfc cracker formulation consisting of tapioca starch, fish paste, and water. the mixture was extruded through a single screw extruder, and the extrudate was cut, dried, heated in a microwave, and the degrees of expansion, bulk density, colour and protein content were measured.
The addition of 1.5 and 3.0% EWP had no significant effect ( P < 0.01) on diametral and longitudinal expansion, however, 4.5% EWP significantly ( P < 0.01) reduced them. Bulk density and protein content of the final product increased as the percentage of EWP increased in the formulation. the total colour difference measurement showed a significant increase ( P < 0.01) in brown colouration at 4.5% EWP.     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.